diff --git a/include/asm-arm/arch-xscale/bitfield.h b/include/asm-arm/arch-pxa/bitfield.h
similarity index 100%
rename from include/asm-arm/arch-xscale/bitfield.h
rename to include/asm-arm/arch-pxa/bitfield.h
diff --git a/include/asm-arm/arch-xscale/hardware.h b/include/asm-arm/arch-pxa/hardware.h
similarity index 100%
rename from include/asm-arm/arch-xscale/hardware.h
rename to include/asm-arm/arch-pxa/hardware.h
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h
index dda2465..208c110 100644
--- a/include/asm-arm/arch-pxa/pxa-regs.h
+++ b/include/asm-arm/arch-pxa/pxa-regs.h
@@ -8,10 +8,16 @@
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
+ *
+ * - 2003/01/20: Robert Schwebel <r.schwebel@pengutronix.de
+ *   Original file taken from linux-2.4.19-rmk4-pxa1. Added some definitions.
+ *   Added include for hardware.h (for __REG definition)
  */
+#ifndef _PXA_REGS_H_
+#define _PXA_REGS_H_
 
-#ifndef PXA_REGS_H
-#define PXA_REGS_H 1
+#include "bitfield.h"
+#include "hardware.h"
 
 /* FIXME hack so that SA-1111.h will work [cb] */
 
@@ -24,13 +30,6 @@
 typedef void            (*ExcpHndlr) (void) ;
 #endif
 
-#ifndef __ASSEMBLY__
-#define io_p2v(PhAdd)    (PhAdd)
-#define __REG(x) (*((volatile u32 *)io_p2v(x)))
-#else
-#define __REG(x) (x)
-#endif
-
 /*
  * PXA Chip selects
  */
@@ -416,7 +415,6 @@
                 IrSR_RCVEIR_UART_MODE | \
                 IrSR_XMITIR_IR_MODE)
 
-
 /*
  * I2C registers
  */
@@ -444,6 +442,7 @@
 #define ICR_ALDIE	0x1000  	/* enable arbitration interrupt */
 #define ICR_SADIE	0x2000		/* slave address detected int enable */
 #define ICR_UR		0x4000		/* unit reset */
+#define ICR_FM		0x8000		/* Fast Mode */
 
 /* ----- Status register bits ----------------------------------------- */
 
@@ -459,7 +458,6 @@
 #define ISR_SAD         0x200		/* slave address detected */
 #define ISR_BED         0x400           /* bus error no ACK/NAK */
 
-
 /*
  * Serial Audio Controller
  */
@@ -558,24 +556,92 @@
 /*
  * USB Device Controller
  */
+#define UDC_RES1	__REG(0x40600004)  /* UDC Undocumented - Reserved1 */
+#define UDC_RES2	__REG(0x40600008)  /* UDC Undocumented - Reserved2 */
+#define UDC_RES3	__REG(0x4060000C)  /* UDC Undocumented - Reserved3 */
 
 #define UDCCR		__REG(0x40600000)  /* UDC Control Register */
+#define UDCCR_UDE	(1 << 0)	/* UDC enable */
+#define UDCCR_UDA	(1 << 1)	/* UDC active */
+#define UDCCR_RSM	(1 << 2)	/* Device resume */
+#define UDCCR_RESIR	(1 << 3)	/* Resume interrupt request */
+#define UDCCR_SUSIR	(1 << 4)	/* Suspend interrupt request */
+#define UDCCR_SRM	(1 << 5)	/* Suspend/resume interrupt mask */
+#define UDCCR_RSTIR	(1 << 6)	/* Reset interrupt request */
+#define UDCCR_REM	(1 << 7)	/* Reset interrupt mask */
+
 #define UDCCS0		__REG(0x40600010)  /* UDC Endpoint 0 Control/Status Register */
+#define UDCCS0_OPR	(1 << 0)	/* OUT packet ready */
+#define UDCCS0_IPR	(1 << 1)	/* IN packet ready */
+#define UDCCS0_FTF	(1 << 2)	/* Flush Tx FIFO */
+#define UDCCS0_DRWF	(1 << 3)	/* Device remote wakeup feature */
+#define UDCCS0_SST	(1 << 4)	/* Sent stall */
+#define UDCCS0_FST	(1 << 5)	/* Force stall */
+#define UDCCS0_RNE	(1 << 6)	/* Receive FIFO no empty */
+#define UDCCS0_SA	(1 << 7)	/* Setup active */
+
+/* Bulk IN - Endpoint 1,6,11 */
 #define UDCCS1		__REG(0x40600014)  /* UDC Endpoint 1 (IN) Control/Status Register */
-#define UDCCS2		__REG(0x40600018)  /* UDC Endpoint 2 (OUT) Control/Status Register */
-#define UDCCS3		__REG(0x4060001C)  /* UDC Endpoint 3 (IN) Control/Status Register */
-#define UDCCS4		__REG(0x40600020)  /* UDC Endpoint 4 (OUT) Control/Status Register */
-#define UDCCS5		__REG(0x40600024)  /* UDC Endpoint 5 (Interrupt) Control/Status Register */
 #define UDCCS6		__REG(0x40600028)  /* UDC Endpoint 6 (IN) Control/Status Register */
-#define UDCCS7		__REG(0x4060002C)  /* UDC Endpoint 7 (OUT) Control/Status Register */
-#define UDCCS8		__REG(0x40600030)  /* UDC Endpoint 8 (IN) Control/Status Register */
-#define UDCCS9		__REG(0x40600034)  /* UDC Endpoint 9 (OUT) Control/Status Register */
-#define UDCCS10		__REG(0x40600038)  /* UDC Endpoint 10 (Interrupt) Control/Status Register */
 #define UDCCS11		__REG(0x4060003C)  /* UDC Endpoint 11 (IN) Control/Status Register */
+
+#define UDCCS_BI_TFS	(1 << 0)	/* Transmit FIFO service */
+#define UDCCS_BI_TPC	(1 << 1)	/* Transmit packet complete */
+#define UDCCS_BI_FTF	(1 << 2)	/* Flush Tx FIFO */
+#define UDCCS_BI_TUR	(1 << 3)	/* Transmit FIFO underrun */
+#define UDCCS_BI_SST	(1 << 4)	/* Sent stall */
+#define UDCCS_BI_FST	(1 << 5)	/* Force stall */
+#define UDCCS_BI_TSP	(1 << 7)	/* Transmit short packet */
+
+/* Bulk OUT - Endpoint 2,7,12 */
+#define UDCCS2		__REG(0x40600018)  /* UDC Endpoint 2 (OUT) Control/Status Register */
+#define UDCCS7		__REG(0x4060002C)  /* UDC Endpoint 7 (OUT) Control/Status Register */
 #define UDCCS12		__REG(0x40600040)  /* UDC Endpoint 12 (OUT) Control/Status Register */
+
+#define UDCCS_BO_RFS	(1 << 0)	/* Receive FIFO service */
+#define UDCCS_BO_RPC	(1 << 1)	/* Receive packet complete */
+#define UDCCS_BO_DME	(1 << 3)	/* DMA enable */
+#define UDCCS_BO_SST	(1 << 4)	/* Sent stall */
+#define UDCCS_BO_FST	(1 << 5)	/* Force stall */
+#define UDCCS_BO_RNE	(1 << 6)	/* Receive FIFO not empty */
+#define UDCCS_BO_RSP	(1 << 7)	/* Receive short packet */
+
+/* Isochronous IN - Endpoint 3,8,13 */
+#define UDCCS3		__REG(0x4060001C)  /* UDC Endpoint 3 (IN) Control/Status Register */
+#define UDCCS8		__REG(0x40600030)  /* UDC Endpoint 8 (IN) Control/Status Register */
 #define UDCCS13		__REG(0x40600044)  /* UDC Endpoint 13 (IN) Control/Status Register */
+
+#define UDCCS_II_TFS	(1 << 0)	/* Transmit FIFO service */
+#define UDCCS_II_TPC	(1 << 1)	/* Transmit packet complete */
+#define UDCCS_II_FTF	(1 << 2)	/* Flush Tx FIFO */
+#define UDCCS_II_TUR	(1 << 3)	/* Transmit FIFO underrun */
+#define UDCCS_II_TSP	(1 << 7)	/* Transmit short packet */
+
+/* Isochronous OUT - Endpoint 4,9,14 */
+#define UDCCS4		__REG(0x40600020)  /* UDC Endpoint 4 (OUT) Control/Status Register */
+#define UDCCS9		__REG(0x40600034)  /* UDC Endpoint 9 (OUT) Control/Status Register */
 #define UDCCS14		__REG(0x40600048)  /* UDC Endpoint 14 (OUT) Control/Status Register */
+
+#define UDCCS_IO_RFS	(1 << 0)	/* Receive FIFO service */
+#define UDCCS_IO_RPC	(1 << 1)	/* Receive packet complete */
+#define UDCCS_IO_ROF	(1 << 3)	/* Receive overflow */
+#define UDCCS_IO_DME	(1 << 3)	/* DMA enable */
+#define UDCCS_IO_RNE	(1 << 6)	/* Receive FIFO not empty */
+#define UDCCS_IO_RSP	(1 << 7)	/* Receive short packet */
+
+/* Interrupt IN - Endpoint 5,10,15 */
+#define UDCCS5		__REG(0x40600024)  /* UDC Endpoint 5 (Interrupt) Control/Status Register */
+#define UDCCS10		__REG(0x40600038)  /* UDC Endpoint 10 (Interrupt) Control/Status Register */
 #define UDCCS15		__REG(0x4060004C)  /* UDC Endpoint 15 (Interrupt) Control/Status Register */
+
+#define UDCCS_INT_TFS	(1 << 0)	/* Transmit FIFO service */
+#define UDCCS_INT_TPC	(1 << 1)	/* Transmit packet complete */
+#define UDCCS_INT_FTF	(1 << 2)	/* Flush Tx FIFO */
+#define UDCCS_INT_TUR	(1 << 3)	/* Transmit FIFO underrun */
+#define UDCCS_INT_SST	(1 << 4)	/* Sent stall */
+#define UDCCS_INT_FST	(1 << 5)	/* Force stall */
+#define UDCCS_INT_TSP	(1 << 7)	/* Transmit short packet */
+
 #define UFNRH		__REG(0x40600060)  /* UDC Frame Number Register High */
 #define UFNRL		__REG(0x40600064)  /* UDC Frame Number Register Low */
 #define UBCR2		__REG(0x40600068)  /* UDC Byte Count Reg 2 */
@@ -600,11 +666,51 @@
 #define UDDR13		__REG(0x40600C00)  /* UDC Endpoint 13 Data Register */
 #define UDDR14		__REG(0x40600E00)  /* UDC Endpoint 14 Data Register */
 #define UDDR15		__REG(0x406000E0)  /* UDC Endpoint 15 Data Register */
+
 #define UICR0		__REG(0x40600050)  /* UDC Interrupt Control Register 0 */
+
+#define UICR0_IM0	(1 << 0)	/* Interrupt mask ep 0 */
+#define UICR0_IM1	(1 << 1)	/* Interrupt mask ep 1 */
+#define UICR0_IM2	(1 << 2)	/* Interrupt mask ep 2 */
+#define UICR0_IM3	(1 << 3)	/* Interrupt mask ep 3 */
+#define UICR0_IM4	(1 << 4)	/* Interrupt mask ep 4 */
+#define UICR0_IM5	(1 << 5)	/* Interrupt mask ep 5 */
+#define UICR0_IM6	(1 << 6)	/* Interrupt mask ep 6 */
+#define UICR0_IM7	(1 << 7)	/* Interrupt mask ep 7 */
+
 #define UICR1		__REG(0x40600054)  /* UDC Interrupt Control Register 1 */
+
+#define UICR1_IM8	(1 << 0)	/* Interrupt mask ep 8 */
+#define UICR1_IM9	(1 << 1)	/* Interrupt mask ep 9 */
+#define UICR1_IM10	(1 << 2)	/* Interrupt mask ep 10 */
+#define UICR1_IM11	(1 << 3)	/* Interrupt mask ep 11 */
+#define UICR1_IM12	(1 << 4)	/* Interrupt mask ep 12 */
+#define UICR1_IM13	(1 << 5)	/* Interrupt mask ep 13 */
+#define UICR1_IM14	(1 << 6)	/* Interrupt mask ep 14 */
+#define UICR1_IM15	(1 << 7)	/* Interrupt mask ep 15 */
+
 #define USIR0		__REG(0x40600058)  /* UDC Status Interrupt Register 0 */
+
+#define USIR0_IR0	(1 << 0)	/* Interrup request ep 0 */
+#define USIR0_IR1	(1 << 1)	/* Interrup request ep 1 */
+#define USIR0_IR2	(1 << 2)	/* Interrup request ep 2 */
+#define USIR0_IR3	(1 << 3)	/* Interrup request ep 3 */
+#define USIR0_IR4	(1 << 4)	/* Interrup request ep 4 */
+#define USIR0_IR5	(1 << 5)	/* Interrup request ep 5 */
+#define USIR0_IR6	(1 << 6)	/* Interrup request ep 6 */
+#define USIR0_IR7	(1 << 7)	/* Interrup request ep 7 */
+
 #define USIR1		__REG(0x4060005C)  /* UDC Status Interrupt Register 1 */
 
+#define USIR1_IR8	(1 << 0)	/* Interrup request ep 8 */
+#define USIR1_IR9	(1 << 1)	/* Interrup request ep 9 */
+#define USIR1_IR10	(1 << 2)	/* Interrup request ep 10 */
+#define USIR1_IR11	(1 << 3)	/* Interrup request ep 11 */
+#define USIR1_IR12	(1 << 4)	/* Interrup request ep 12 */
+#define USIR1_IR13	(1 << 5)	/* Interrup request ep 13 */
+#define USIR1_IR14	(1 << 6)	/* Interrup request ep 14 */
+#define USIR1_IR15	(1 << 7)	/* Interrup request ep 15 */
+
 
 /*
  * Fast Infrared Communication Port
@@ -951,6 +1057,22 @@
 #define PGSR2		__REG(0x40F00028)  /* Power Manager GPIO Sleep State Register for GP[84-64] */
 #define RCSR		__REG(0x40F00030)  /* Reset Controller Status Register */
 
+#define PSSR_RDH	(1 << 5)	/* Read Disable Hold */
+#define PSSR_PH		(1 << 4)	/* Peripheral Control Hold */
+#define PSSR_VFS	(1 << 2)	/* VDD Fault Status */
+#define PSSR_BFS	(1 << 1)	/* Battery Fault Status */
+#define PSSR_SSS	(1 << 0)	/* Software Sleep Status */
+
+#define PCFR_DS		(1 << 3)	/* Deep Sleep Mode */
+#define PCFR_FS		(1 << 2)	/* Float Static Chip Selects */
+#define PCFR_FP		(1 << 1)	/* Float PCMCIA controls */
+#define PCFR_OPDE	(1 << 0)	/* 3.6864 MHz oscillator power-down enable */
+
+#define RCSR_GPR	(1 << 3)	/* GPIO Reset */
+#define RCSR_SMR	(1 << 2)	/* Sleep Mode */
+#define RCSR_WDR	(1 << 1)	/* Watchdog Reset */
+#define RCSR_HWR	(1 << 0)	/* Hardware Reset */
+
 
 /*
  * SSP Serial Port Registers
@@ -1074,19 +1196,105 @@
 #define LCCR0_BM	(1 << 20) 	/* Branch mask */
 #define LCCR0_OUM	(1 << 21)	/* Output FIFO underrun mask */
 
+#define LCCR1_PPL       Fld (10, 0)      /* Pixels Per Line - 1 */
+#define LCCR1_DisWdth(Pixel)            /* Display Width [1..800 pix.]  */ \
+                        (((Pixel) - 1) << FShft (LCCR1_PPL))
+
+#define LCCR1_HSW       Fld (6, 10)     /* Horizontal Synchronization     */
+#define LCCR1_HorSnchWdth(Tpix)         /* Horizontal Synchronization     */ \
+                                        /* pulse Width [1..64 Tpix]       */ \
+                        (((Tpix) - 1) << FShft (LCCR1_HSW))
+
+#define LCCR1_ELW       Fld (8, 16)     /* End-of-Line pixel clock Wait    */
+                                        /* count - 1 [Tpix]                */
+#define LCCR1_EndLnDel(Tpix)            /*  End-of-Line Delay              */ \
+                                        /*  [1..256 Tpix]                  */ \
+                        (((Tpix) - 1) << FShft (LCCR1_ELW))
+
+#define LCCR1_BLW       Fld (8, 24)     /* Beginning-of-Line pixel clock   */
+                                        /* Wait count - 1 [Tpix]           */
+#define LCCR1_BegLnDel(Tpix)            /*  Beginning-of-Line Delay        */ \
+                                        /*  [1..256 Tpix]                  */ \
+                        (((Tpix) - 1) << FShft (LCCR1_BLW))
+
+
+#define LCCR2_LPP       Fld (10, 0)     /* Line Per Panel - 1              */
+#define LCCR2_DisHght(Line)             /*  Display Height [1..1024 lines] */ \
+                        (((Line) - 1) << FShft (LCCR2_LPP))
+
+#define LCCR2_VSW       Fld (6, 10)     /* Vertical Synchronization pulse  */
+                                        /* Width - 1 [Tln] (L_FCLK)        */
+#define LCCR2_VrtSnchWdth(Tln)          /*  Vertical Synchronization pulse */ \
+                                        /*  Width [1..64 Tln]              */ \
+                        (((Tln) - 1) << FShft (LCCR2_VSW))
+
+#define LCCR2_EFW       Fld (8, 16)     /* End-of-Frame line clock Wait    */
+                                        /* count [Tln]                     */
+#define LCCR2_EndFrmDel(Tln)            /*  End-of-Frame Delay             */ \
+                                        /*  [0..255 Tln]                   */ \
+                        ((Tln) << FShft (LCCR2_EFW))
+
+#define LCCR2_BFW       Fld (8, 24)     /* Beginning-of-Frame line clock   */
+                                        /* Wait count [Tln]                */
+#define LCCR2_BegFrmDel(Tln)            /*  Beginning-of-Frame Delay       */ \
+                                        /*  [0..255 Tln]                   */ \
+                        ((Tln) << FShft (LCCR2_BFW))
+
+#if 0
 #define LCCR3_PCD	(0xff)		/* Pixel clock divisor */
 #define LCCR3_ACB	(0xff << 8)	/* AC Bias pin frequency */
 #define LCCR3_ACB_S	8
+#endif
+
 #define LCCR3_API	(0xf << 16)	/* AC Bias pin trasitions per interrupt */
 #define LCCR3_API_S	16
 #define LCCR3_VSP	(1 << 20)	/* vertical sync polarity */
 #define LCCR3_HSP	(1 << 21)	/* horizontal sync polarity */
 #define LCCR3_PCP	(1 << 22)	/* pixel clock polarity */
 #define LCCR3_OEP	(1 << 23)	/* output enable polarity */
+#if 0
 #define LCCR3_BPP	(7 << 24)	/* bits per pixel */
 #define LCCR3_BPP_S	24
+#endif
 #define LCCR3_DPC	(1 << 27)	/* double pixel clock mode */
 
+
+#define LCCR3_PCD       Fld (8, 0)      /* Pixel Clock Divisor */
+#define LCCR3_PixClkDiv(Div)            /* Pixel Clock Divisor */ \
+                        (((Div) << FShft (LCCR3_PCD)))
+
+
+#define LCCR3_BPP       Fld (3, 24)     /* Bit Per Pixel */
+#define LCCR3_Bpp(Bpp)                  /* Bit Per Pixel */ \
+                        (((Bpp) << FShft (LCCR3_BPP)))
+
+#define LCCR3_ACB       Fld (8, 8)      /* AC Bias */
+#define LCCR3_Acb(Acb)                  /* BAC Bias */ \
+                        (((Acb) << FShft (LCCR3_ACB)))
+
+#define LCCR3_HorSnchH  (LCCR3_HSP*0)   /*  Horizontal Synchronization     */
+                                        /*  pulse active High              */
+#define LCCR3_HorSnchL  (LCCR3_HSP*1)   /*  Horizontal Synchronization     */
+
+#define LCCR3_VrtSnchH  (LCCR3_VSP*0)   /*  Vertical Synchronization pulse */
+                                        /*  active High                    */
+#define LCCR3_VrtSnchL  (LCCR3_VSP*1)   /*  Vertical Synchronization pulse */
+                                        /*  active Low                     */
+
+#define LCSR_LDD	(1 << 0)	/* LCD Disable Done */
+#define LCSR_SOF	(1 << 1)	/* Start of frame */
+#define LCSR_BER	(1 << 2)	/* Bus error */
+#define LCSR_ABC	(1 << 3)	/* AC Bias count */
+#define LCSR_IUL	(1 << 4)	/* input FIFO underrun Lower panel */
+#define LCSR_IUU	(1 << 5)	/* input FIFO underrun Upper panel */
+#define LCSR_OU		(1 << 6)	/* output FIFO underrun */
+#define LCSR_QD		(1 << 7)	/* quick disable */
+#define LCSR_EOF	(1 << 8)	/* end of frame */
+#define LCSR_BS		(1 << 9)	/* branch status */
+#define LCSR_SINT	(1 << 10)	/* subsequent interrupt */
+
+#define LDCMD_PAL	(1 << 26)	/* instructs DMA to load palette buffer */
+
 #define LCSR_LDD	(1 << 0)	/* LCD Disable Done */
 #define LCSR_SOF	(1 << 1)	/* Start of frame */
 #define LCSR_BER	(1 << 2)	/* Bus error */
@@ -1105,45 +1313,7 @@
  * Memory controller
  */
 
-#define MEMC_BASE __REG(0x48000000)  /* Base of Memoriy Controller */
-#define MDCNFG		__REG(0x48000000)  /* SDRAM Configuration Register 0 */
-#define MDREFR		__REG(0x48000004)  /* SDRAM Refresh Control Register */
-#define MSC0		__REG(0x48000008)  /* Static Memory Control Register 0 */
-#define MSC1		__REG(0x4800000C)  /* Static Memory Control Register 1 */
-#define MSC2		__REG(0x48000010)  /* Static Memory Control Register 2 */
-#define MECR		__REG(0x48000014)  /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
-#define SXLCR		__REG(0x48000018)  /* LCR value to be written to SDRAM-Timing Synchronous Flash */
-#define SXCNFG		__REG(0x4800001C)  /* Synchronous Static Memory Control Register */
-#define SXMRS		__REG(0x48000024)  /* MRS value to be written to Synchronous Flash or SMROM */
-#define MCMEM0		__REG(0x48000028)  /* Card interface Common Memory Space Socket 0 Timing */
-#define MCMEM1		__REG(0x4800002C)  /* Card interface Common Memory Space Socket 1 Timing */
-#define MCATT0		__REG(0x48000030)  /* Card interface Attribute Space Socket 0 Timing Configuration */
-#define MCATT1		__REG(0x48000034)  /* Card interface Attribute Space Socket 1 Timing Configuration */
-#define MCIO0		__REG(0x48000038)  /* Card interface I/O Space Socket 0 Timing Configuration */
-#define MCIO1		__REG(0x4800003C)  /* Card interface I/O Space Socket 1 Timing Configuration */
-#define MDMRS		__REG(0x48000040)  /* MRS value to be written to SDRAM */
-#define BOOT_DEF	__REG(0x48000044)  /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
-
-#define MDCNFG_DE0      0x00000001
-#define MDCNFG_DE1      0x00000002
-#define MDCNFG_DE2      0x00010000
-#define MDCNFG_DE3      0x00020000
-#define MDCNFG_DWID0    0x00000004
-
-#define MDREFR_E0PIN    0x00001000
-#define MDREFR_K0RUN	0x00002000
-#define MDREFR_K0DB2	0x00004000
-#define MDREFR_E1PIN    0x00008000
-#define MDREFR_K1RUN	0x00010000
-#define MDREFR_K1DB2	0x00020000
-#define MDREFR_K2RUN	0x00040000
-#define MDREFR_K2DB2	0x00080000
-#define MDREFR_APD	0x00100000
-#define MDREFR_SLFRSH	0x00400000
-#define MDREFR_K0FREE	0x00800000
-#define MDREFR_K1FREE	0x01000000
-#define MDREFR_K2FREE	0x02000000
-
+#define MEMC_BASE	__REG(0x48000000)  /* Base of Memory Controller */
 #define MDCNFG_OFFSET   0x0
 #define MDREFR_OFFSET   0x4
 #define MSC0_OFFSET     0x8
@@ -1162,6 +1332,43 @@
 #define MCIO1_OFFSET    0x3C
 #define MDMRS_OFFSET    0x40
 
-#endif /* PXA_REGS_H */
+#define MDCNFG		__REG(0x48000000)  /* SDRAM Configuration Register 0 */
+#define MDCNFG_DE0	0x00000001
+#define MDCNFG_DE1	0x00000002
+#define MDCNFG_DE2	0x00010000
+#define MDCNFG_DE3	0x00020000
+#define MDCNFG_DWID0	0x00000004
+	
+#define MDREFR		__REG(0x48000004)  /* SDRAM Refresh Control Register */
+#define MSC0		__REG(0x48000008)  /* Static Memory Control Register 0 */
+#define MSC1		__REG(0x4800000C)  /* Static Memory Control Register 1 */
+#define MSC2		__REG(0x48000010)  /* Static Memory Control Register 2 */
+#define MECR		__REG(0x48000014)  /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
+#define SXLCR		__REG(0x48000018)  /* LCR value to be written to SDRAM-Timing Synchronous Flash */
+#define SXCNFG		__REG(0x4800001C)  /* Synchronous Static Memory Control Register */
+#define SXMRS		__REG(0x48000024)  /* MRS value to be written to Synchronous Flash or SMROM */
+#define MCMEM0		__REG(0x48000028)  /* Card interface Common Memory Space Socket 0 Timing */
+#define MCMEM1		__REG(0x4800002C)  /* Card interface Common Memory Space Socket 1 Timing */
+#define MCATT0		__REG(0x48000030)  /* Card interface Attribute Space Socket 0 Timing Configuration */
+#define MCATT1		__REG(0x48000034)  /* Card interface Attribute Space Socket 1 Timing Configuration */
+#define MCIO0		__REG(0x48000038)  /* Card interface I/O Space Socket 0 Timing Configuration */
+#define MCIO1		__REG(0x4800003C)  /* Card interface I/O Space Socket 1 Timing Configuration */
+#define MDMRS		__REG(0x48000040)  /* MRS value to be written to SDRAM */
+#define BOOT_DEF	__REG(0x48000044)  /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
+
+#define MDREFR_K2FREE	(1 << 25)	/* SDRAM Free-Running Control */
+#define MDREFR_K1FREE	(1 << 24)	/* SDRAM Free-Running Control */
+#define MDREFR_K0FREE	(1 << 23)	/* SDRAM Free-Running Control */
+#define MDREFR_SLFRSH	(1 << 22)	/* SDRAM Self-Refresh Control/Status */
+#define MDREFR_APD	(1 << 20)	/* SDRAM/SSRAM Auto-Power-Down Enable */
+#define MDREFR_K2DB2	(1 << 19)	/* SDCLK2 Divide by 2 Control/Status */
+#define MDREFR_K2RUN	(1 << 18)	/* SDCLK2 Run Control/Status */
+#define MDREFR_K1DB2	(1 << 17)	/* SDCLK1 Divide by 2 Control/Status */
+#define MDREFR_K1RUN	(1 << 16)	/* SDCLK1 Run Control/Status */
+#define MDREFR_E1PIN	(1 << 15)	/* SDCKE1 Level Control/Status */
+#define MDREFR_K0DB2	(1 << 14)	/* SDCLK0 Divide by 2 Control/Status */
+#define MDREFR_K0RUN	(1 << 13)	/* SDCLK0 Run Control/Status */
+#define MDREFR_E0PIN	(1 << 12)	/* SDCKE0 Level Control/Status */
 
 
+#endif
diff --git a/include/asm-arm/arch-xscale/pxa-regs.h b/include/asm-arm/arch-xscale/pxa-regs.h
deleted file mode 100644
index 449ec9f..0000000
--- a/include/asm-arm/arch-xscale/pxa-regs.h
+++ /dev/null
@@ -1,1374 +0,0 @@
-/*
- *  linux/include/asm-arm/arch-pxa/pxa-regs.h
- *  
- *  Author:	Nicolas Pitre
- *  Created:	Jun 15, 2001
- *  Copyright:	MontaVista Software Inc.
- *  
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * - 2003/01/20: Robert Schwebel <r.schwebel@pengutronix.de
- *   Original file taken from linux-2.4.19-rmk4-pxa1. Added some definitions.
- *   Added include for hardware.h (for __REG definition)
- */
-#ifndef _PXA_REGS_H_
-#define _PXA_REGS_H_
-
-#include "bitfield.h"
-#include "hardware.h"
-
-/* FIXME hack so that SA-1111.h will work [cb] */
-
-#ifndef __ASSEMBLY__
-typedef unsigned short  Word16 ;
-typedef unsigned int    Word32 ;
-typedef Word32          Word ;
-typedef Word            Quad [4] ;
-typedef void            *Address ;
-typedef void            (*ExcpHndlr) (void) ;
-#endif
-
-/*
- * PXA Chip selects
- */
-
-#define PXA_CS0_PHYS	0x00000000
-#define PXA_CS1_PHYS	0x04000000
-#define PXA_CS2_PHYS	0x08000000
-#define PXA_CS3_PHYS	0x0C000000
-#define PXA_CS4_PHYS	0x10000000
-#define PXA_CS5_PHYS	0x14000000
-
-
-/*
- * Personal Computer Memory Card International Association (PCMCIA) sockets
- */
-
-#define PCMCIAPrtSp	0x04000000	/* PCMCIA Partition Space [byte]   */
-#define PCMCIASp	(4*PCMCIAPrtSp)	/* PCMCIA Space [byte]             */
-#define PCMCIAIOSp	PCMCIAPrtSp	/* PCMCIA I/O Space [byte]         */
-#define PCMCIAAttrSp	PCMCIAPrtSp	/* PCMCIA Attribute Space [byte]   */
-#define PCMCIAMemSp	PCMCIAPrtSp	/* PCMCIA Memory Space [byte]      */
-
-#define PCMCIA0Sp	PCMCIASp	/* PCMCIA 0 Space [byte]           */
-#define PCMCIA0IOSp	PCMCIAIOSp	/* PCMCIA 0 I/O Space [byte]       */
-#define PCMCIA0AttrSp	PCMCIAAttrSp	/* PCMCIA 0 Attribute Space [byte] */
-#define PCMCIA0MemSp	PCMCIAMemSp	/* PCMCIA 0 Memory Space [byte]    */
-
-#define PCMCIA1Sp	PCMCIASp	/* PCMCIA 1 Space [byte]           */
-#define PCMCIA1IOSp	PCMCIAIOSp	/* PCMCIA 1 I/O Space [byte]       */
-#define PCMCIA1AttrSp	PCMCIAAttrSp	/* PCMCIA 1 Attribute Space [byte] */
-#define PCMCIA1MemSp	PCMCIAMemSp	/* PCMCIA 1 Memory Space [byte]    */
-
-#define _PCMCIA(Nb)	        	/* PCMCIA [0..1]                   */ \
-                	(0x20000000 + (Nb)*PCMCIASp)
-#define _PCMCIAIO(Nb)	_PCMCIA (Nb)	/* PCMCIA I/O [0..1]               */
-#define _PCMCIAAttr(Nb)	        	/* PCMCIA Attribute [0..1]         */ \
-                	(_PCMCIA (Nb) + 2*PCMCIAPrtSp)
-#define _PCMCIAMem(Nb)	        	/* PCMCIA Memory [0..1]            */ \
-                	(_PCMCIA (Nb) + 3*PCMCIAPrtSp)
-
-#define _PCMCIA0	_PCMCIA (0)	/* PCMCIA 0                        */
-#define _PCMCIA0IO	_PCMCIAIO (0)	/* PCMCIA 0 I/O                    */
-#define _PCMCIA0Attr	_PCMCIAAttr (0)	/* PCMCIA 0 Attribute              */
-#define _PCMCIA0Mem	_PCMCIAMem (0)	/* PCMCIA 0 Memory                 */
-
-#define _PCMCIA1	_PCMCIA (1)	/* PCMCIA 1                        */
-#define _PCMCIA1IO	_PCMCIAIO (1)	/* PCMCIA 1 I/O                    */
-#define _PCMCIA1Attr	_PCMCIAAttr (1)	/* PCMCIA 1 Attribute              */
-#define _PCMCIA1Mem	_PCMCIAMem (1)	/* PCMCIA 1 Memory                 */
-
-
-
-/*
- * DMA Controller
- */
-
-#define DCSR0		__REG(0x40000000)  /* DMA Control / Status Register for Channel 0 */
-#define DCSR1		__REG(0x40000004)  /* DMA Control / Status Register for Channel 1 */
-#define DCSR2		__REG(0x40000008)  /* DMA Control / Status Register for Channel 2 */
-#define DCSR3		__REG(0x4000000c)  /* DMA Control / Status Register for Channel 3 */
-#define DCSR4		__REG(0x40000010)  /* DMA Control / Status Register for Channel 4 */
-#define DCSR5		__REG(0x40000014)  /* DMA Control / Status Register for Channel 5 */
-#define DCSR6		__REG(0x40000018)  /* DMA Control / Status Register for Channel 6 */
-#define DCSR7		__REG(0x4000001c)  /* DMA Control / Status Register for Channel 7 */
-#define DCSR8		__REG(0x40000020)  /* DMA Control / Status Register for Channel 8 */
-#define DCSR9		__REG(0x40000024)  /* DMA Control / Status Register for Channel 9 */
-#define DCSR10		__REG(0x40000028)  /* DMA Control / Status Register for Channel 10 */
-#define DCSR11		__REG(0x4000002c)  /* DMA Control / Status Register for Channel 11 */
-#define DCSR12		__REG(0x40000030)  /* DMA Control / Status Register for Channel 12 */
-#define DCSR13		__REG(0x40000034)  /* DMA Control / Status Register for Channel 13 */
-#define DCSR14		__REG(0x40000038)  /* DMA Control / Status Register for Channel 14 */
-#define DCSR15		__REG(0x4000003c)  /* DMA Control / Status Register for Channel 15 */
-
-#define DCSR(x)		__REG2(0x40000000, (x) << 2)
-
-#define DCSR_RUN	(1 << 31)	/* Run Bit (read / write) */
-#define DCSR_NODESC	(1 << 30)	/* No-Descriptor Fetch (read / write) */
-#define DCSR_STOPIRQEN	(1 << 29)	/* Stop Interrupt Enable (read / write) */
-#define DCSR_REQPEND	(1 << 8)	/* Request Pending (read-only) */
-#define DCSR_STOPSTATE	(1 << 3)	/* Stop State (read-only) */
-#define DCSR_ENDINTR	(1 << 2)	/* End Interrupt (read / write) */
-#define DCSR_STARTINTR	(1 << 1)	/* Start Interrupt (read / write) */
-#define DCSR_BUSERR	(1 << 0)	/* Bus Error Interrupt (read / write) */
-
-#define DINT		__REG(0x400000f0)  /* DMA Interrupt Register */
-
-#define DRCMR0		__REG(0x40000100)  /* Request to Channel Map Register for DREQ 0 */
-#define DRCMR1		__REG(0x40000104)  /* Request to Channel Map Register for DREQ 1 */
-#define DRCMR2		__REG(0x40000108)  /* Request to Channel Map Register for I2S receive Request */
-#define DRCMR3		__REG(0x4000010c)  /* Request to Channel Map Register for I2S transmit Request */
-#define DRCMR4		__REG(0x40000110)  /* Request to Channel Map Register for BTUART receive Request */
-#define DRCMR5		__REG(0x40000114)  /* Request to Channel Map Register for BTUART transmit Request. */
-#define DRCMR6		__REG(0x40000118)  /* Request to Channel Map Register for FFUART receive Request */
-#define DRCMR7		__REG(0x4000011c)  /* Request to Channel Map Register for FFUART transmit Request */
-#define DRCMR8		__REG(0x40000120)  /* Request to Channel Map Register for AC97 microphone Request */
-#define DRCMR9		__REG(0x40000124)  /* Request to Channel Map Register for AC97 modem receive Request */
-#define DRCMR10		__REG(0x40000128)  /* Request to Channel Map Register for AC97 modem transmit Request */
-#define DRCMR11		__REG(0x4000012c)  /* Request to Channel Map Register for AC97 audio receive Request */
-#define DRCMR12		__REG(0x40000130)  /* Request to Channel Map Register for AC97 audio transmit Request */
-#define DRCMR13		__REG(0x40000134)  /* Request to Channel Map Register for SSP receive Request */
-#define DRCMR14		__REG(0x40000138)  /* Request to Channel Map Register for SSP transmit Request */
-#define DRCMR15		__REG(0x4000013c)  /* Reserved */
-#define DRCMR16		__REG(0x40000140)  /* Reserved */
-#define DRCMR17		__REG(0x40000144)  /* Request to Channel Map Register for ICP receive Request */
-#define DRCMR18		__REG(0x40000148)  /* Request to Channel Map Register for ICP transmit Request */
-#define DRCMR19		__REG(0x4000014c)  /* Request to Channel Map Register for STUART receive Request */
-#define DRCMR20		__REG(0x40000150)  /* Request to Channel Map Register for STUART transmit Request */
-#define DRCMR21		__REG(0x40000154)  /* Request to Channel Map Register for MMC receive Request */
-#define DRCMR22		__REG(0x40000158)  /* Request to Channel Map Register for MMC transmit Request */
-#define DRCMR23		__REG(0x4000015c)  /* Reserved */
-#define DRCMR24		__REG(0x40000160)  /* Reserved */
-#define DRCMR25		__REG(0x40000164)  /* Request to Channel Map Register for USB endpoint 1 Request */
-#define DRCMR26		__REG(0x40000168)  /* Request to Channel Map Register for USB endpoint 2 Request */
-#define DRCMR27		__REG(0x4000016C)  /* Request to Channel Map Register for USB endpoint 3 Request */
-#define DRCMR28		__REG(0x40000170)  /* Request to Channel Map Register for USB endpoint 4 Request */
-#define DRCMR29		__REG(0x40000174)  /* Reserved */
-#define DRCMR30		__REG(0x40000178)  /* Request to Channel Map Register for USB endpoint 6 Request */
-#define DRCMR31		__REG(0x4000017C)  /* Request to Channel Map Register for USB endpoint 7 Request */
-#define DRCMR32		__REG(0x40000180)  /* Request to Channel Map Register for USB endpoint 8 Request */
-#define DRCMR33		__REG(0x40000184)  /* Request to Channel Map Register for USB endpoint 9 Request */
-#define DRCMR34		__REG(0x40000188)  /* Reserved */
-#define DRCMR35		__REG(0x4000018C)  /* Request to Channel Map Register for USB endpoint 11 Request */
-#define DRCMR36		__REG(0x40000190)  /* Request to Channel Map Register for USB endpoint 12 Request */
-#define DRCMR37		__REG(0x40000194)  /* Request to Channel Map Register for USB endpoint 13 Request */
-#define DRCMR38		__REG(0x40000198)  /* Request to Channel Map Register for USB endpoint 14 Request */
-#define DRCMR39		__REG(0x4000019C)  /* Reserved */
-
-#define DRCMRRXSADR	DRCMR2
-#define DRCMRTXSADR	DRCMR3
-#define DRCMRRXBTRBR	DRCMR4
-#define DRCMRTXBTTHR	DRCMR5
-#define DRCMRRXFFRBR	DRCMR6
-#define DRCMRTXFFTHR	DRCMR7
-#define DRCMRRXMCDR	DRCMR8
-#define DRCMRRXMODR	DRCMR9
-#define DRCMRTXMODR	DRCMR10
-#define DRCMRRXPCDR	DRCMR11
-#define DRCMRTXPCDR	DRCMR12
-#define DRCMRRXSSDR	DRCMR13
-#define DRCMRTXSSDR	DRCMR14
-#define DRCMRRXICDR	DRCMR17
-#define DRCMRTXICDR	DRCMR18
-#define DRCMRRXSTRBR	DRCMR19
-#define DRCMRTXSTTHR	DRCMR20
-#define DRCMRRXMMC	DRCMR21
-#define DRCMRTXMMC	DRCMR22
-
-#define DRCMR_MAPVLD	(1 << 7)	/* Map Valid (read / write) */
-#define DRCMR_CHLNUM	0x0f		/* mask for Channel Number (read / write) */
-
-#define DDADR0		__REG(0x40000200)  /* DMA Descriptor Address Register Channel 0 */
-#define DSADR0		__REG(0x40000204)  /* DMA Source Address Register Channel 0 */
-#define DTADR0		__REG(0x40000208)  /* DMA Target Address Register Channel 0 */
-#define DCMD0		__REG(0x4000020c)  /* DMA Command Address Register Channel 0 */
-#define DDADR1		__REG(0x40000210)  /* DMA Descriptor Address Register Channel 1 */
-#define DSADR1		__REG(0x40000214)  /* DMA Source Address Register Channel 1 */
-#define DTADR1		__REG(0x40000218)  /* DMA Target Address Register Channel 1 */
-#define DCMD1		__REG(0x4000021c)  /* DMA Command Address Register Channel 1 */
-#define DDADR2		__REG(0x40000220)  /* DMA Descriptor Address Register Channel 2 */
-#define DSADR2		__REG(0x40000224)  /* DMA Source Address Register Channel 2 */
-#define DTADR2		__REG(0x40000228)  /* DMA Target Address Register Channel 2 */
-#define DCMD2		__REG(0x4000022c)  /* DMA Command Address Register Channel 2 */
-#define DDADR3		__REG(0x40000230)  /* DMA Descriptor Address Register Channel 3 */
-#define DSADR3		__REG(0x40000234)  /* DMA Source Address Register Channel 3 */
-#define DTADR3		__REG(0x40000238)  /* DMA Target Address Register Channel 3 */
-#define DCMD3		__REG(0x4000023c)  /* DMA Command Address Register Channel 3 */
-#define DDADR4		__REG(0x40000240)  /* DMA Descriptor Address Register Channel 4 */
-#define DSADR4		__REG(0x40000244)  /* DMA Source Address Register Channel 4 */
-#define DTADR4		__REG(0x40000248)  /* DMA Target Address Register Channel 4 */
-#define DCMD4		__REG(0x4000024c)  /* DMA Command Address Register Channel 4 */
-#define DDADR5		__REG(0x40000250)  /* DMA Descriptor Address Register Channel 5 */
-#define DSADR5		__REG(0x40000254)  /* DMA Source Address Register Channel 5 */
-#define DTADR5		__REG(0x40000258)  /* DMA Target Address Register Channel 5 */
-#define DCMD5		__REG(0x4000025c)  /* DMA Command Address Register Channel 5 */
-#define DDADR6		__REG(0x40000260)  /* DMA Descriptor Address Register Channel 6 */
-#define DSADR6		__REG(0x40000264)  /* DMA Source Address Register Channel 6 */
-#define DTADR6		__REG(0x40000268)  /* DMA Target Address Register Channel 6 */
-#define DCMD6		__REG(0x4000026c)  /* DMA Command Address Register Channel 6 */
-#define DDADR7		__REG(0x40000270)  /* DMA Descriptor Address Register Channel 7 */
-#define DSADR7		__REG(0x40000274)  /* DMA Source Address Register Channel 7 */
-#define DTADR7		__REG(0x40000278)  /* DMA Target Address Register Channel 7 */
-#define DCMD7		__REG(0x4000027c)  /* DMA Command Address Register Channel 7 */
-#define DDADR8		__REG(0x40000280)  /* DMA Descriptor Address Register Channel 8 */
-#define DSADR8		__REG(0x40000284)  /* DMA Source Address Register Channel 8 */
-#define DTADR8		__REG(0x40000288)  /* DMA Target Address Register Channel 8 */
-#define DCMD8		__REG(0x4000028c)  /* DMA Command Address Register Channel 8 */
-#define DDADR9		__REG(0x40000290)  /* DMA Descriptor Address Register Channel 9 */
-#define DSADR9		__REG(0x40000294)  /* DMA Source Address Register Channel 9 */
-#define DTADR9		__REG(0x40000298)  /* DMA Target Address Register Channel 9 */
-#define DCMD9		__REG(0x4000029c)  /* DMA Command Address Register Channel 9 */
-#define DDADR10		__REG(0x400002a0)  /* DMA Descriptor Address Register Channel 10 */
-#define DSADR10		__REG(0x400002a4)  /* DMA Source Address Register Channel 10 */
-#define DTADR10		__REG(0x400002a8)  /* DMA Target Address Register Channel 10 */
-#define DCMD10		__REG(0x400002ac)  /* DMA Command Address Register Channel 10 */
-#define DDADR11		__REG(0x400002b0)  /* DMA Descriptor Address Register Channel 11 */
-#define DSADR11		__REG(0x400002b4)  /* DMA Source Address Register Channel 11 */
-#define DTADR11		__REG(0x400002b8)  /* DMA Target Address Register Channel 11 */
-#define DCMD11		__REG(0x400002bc)  /* DMA Command Address Register Channel 11 */
-#define DDADR12		__REG(0x400002c0)  /* DMA Descriptor Address Register Channel 12 */
-#define DSADR12		__REG(0x400002c4)  /* DMA Source Address Register Channel 12 */
-#define DTADR12		__REG(0x400002c8)  /* DMA Target Address Register Channel 12 */
-#define DCMD12		__REG(0x400002cc)  /* DMA Command Address Register Channel 12 */
-#define DDADR13		__REG(0x400002d0)  /* DMA Descriptor Address Register Channel 13 */
-#define DSADR13		__REG(0x400002d4)  /* DMA Source Address Register Channel 13 */
-#define DTADR13		__REG(0x400002d8)  /* DMA Target Address Register Channel 13 */
-#define DCMD13		__REG(0x400002dc)  /* DMA Command Address Register Channel 13 */
-#define DDADR14		__REG(0x400002e0)  /* DMA Descriptor Address Register Channel 14 */
-#define DSADR14		__REG(0x400002e4)  /* DMA Source Address Register Channel 14 */
-#define DTADR14		__REG(0x400002e8)  /* DMA Target Address Register Channel 14 */
-#define DCMD14		__REG(0x400002ec)  /* DMA Command Address Register Channel 14 */
-#define DDADR15		__REG(0x400002f0)  /* DMA Descriptor Address Register Channel 15 */
-#define DSADR15		__REG(0x400002f4)  /* DMA Source Address Register Channel 15 */
-#define DTADR15		__REG(0x400002f8)  /* DMA Target Address Register Channel 15 */
-#define DCMD15		__REG(0x400002fc)  /* DMA Command Address Register Channel 15 */
-
-#define DDADR(x)	__REG2(0x40000200, (x) << 4)
-#define DSADR(x)	__REG2(0x40000204, (x) << 4)
-#define DTADR(x)	__REG2(0x40000208, (x) << 4)
-#define DCMD(x)		__REG2(0x4000020c, (x) << 4)
-
-#define DDADR_DESCADDR	0xfffffff0	/* Address of next descriptor (mask) */
-#define DDADR_STOP	(1 << 0)	/* Stop (read / write) */
-
-#define DCMD_INCSRCADDR	(1 << 31)	/* Source Address Increment Setting. */
-#define DCMD_INCTRGADDR	(1 << 30)	/* Target Address Increment Setting. */
-#define DCMD_FLOWSRC	(1 << 29)	/* Flow Control by the source. */
-#define DCMD_FLOWTRG	(1 << 28)	/* Flow Control by the target. */
-#define DCMD_STARTIRQEN	(1 << 22)	/* Start Interrupt Enable */
-#define DCMD_ENDIRQEN	(1 << 21)	/* End Interrupt Enable */
-#define DCMD_ENDIAN	(1 << 18)	/* Device Endian-ness. */
-#define DCMD_BURST8	(1 << 16)	/* 8 byte burst */
-#define DCMD_BURST16	(2 << 16)	/* 16 byte burst */
-#define DCMD_BURST32	(3 << 16)	/* 32 byte burst */
-#define DCMD_WIDTH1	(1 << 14)	/* 1 byte width */
-#define DCMD_WIDTH2	(2 << 14)	/* 2 byte width (HalfWord) */
-#define DCMD_WIDTH4	(3 << 14)	/* 4 byte width (Word) */
-#define DCMD_LENGTH	0x01fff		/* length mask (max = 8K - 1) */
-
-/* default combinations */
-#define DCMD_RXPCDR	(DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_RXMCDR	(DCMD_INCTRGADDR|DCMD_FLOWSRC|DCMD_BURST32|DCMD_WIDTH4)
-#define DCMD_TXPCDR	(DCMD_INCSRCADDR|DCMD_FLOWTRG|DCMD_BURST32|DCMD_WIDTH4)
-
-
-/*
- * UARTs
- */
-
-/* Full Function UART (FFUART) */
-#define FFUART		FFRBR
-#define FFRBR		__REG(0x40100000)  /* Receive Buffer Register (read only) */
-#define FFTHR		__REG(0x40100000)  /* Transmit Holding Register (write only) */
-#define FFIER		__REG(0x40100004)  /* Interrupt Enable Register (read/write) */
-#define FFIIR		__REG(0x40100008)  /* Interrupt ID Register (read only) */
-#define FFFCR		__REG(0x40100008)  /* FIFO Control Register (write only) */
-#define FFLCR		__REG(0x4010000C)  /* Line Control Register (read/write) */
-#define FFMCR		__REG(0x40100010)  /* Modem Control Register (read/write) */
-#define FFLSR		__REG(0x40100014)  /* Line Status Register (read only) */
-#define FFMSR		__REG(0x40100018)  /* Modem Status Register (read only) */
-#define FFSPR		__REG(0x4010001C)  /* Scratch Pad Register (read/write) */
-#define FFISR		__REG(0x40100020)  /* Infrared Selection Register (read/write) */
-#define FFDLL		__REG(0x40100000)  /* Divisor Latch Low Register (DLAB = 1) (read/write) */
-#define FFDLH		__REG(0x40100004)  /* Divisor Latch High Register (DLAB = 1) (read/write) */
-
-/* Bluetooth UART (BTUART) */
-#define BTUART		BTRBR
-#define BTRBR		__REG(0x40200000)  /* Receive Buffer Register (read only) */
-#define BTTHR		__REG(0x40200000)  /* Transmit Holding Register (write only) */
-#define BTIER		__REG(0x40200004)  /* Interrupt Enable Register (read/write) */
-#define BTIIR		__REG(0x40200008)  /* Interrupt ID Register (read only) */
-#define BTFCR		__REG(0x40200008)  /* FIFO Control Register (write only) */
-#define BTLCR		__REG(0x4020000C)  /* Line Control Register (read/write) */
-#define BTMCR		__REG(0x40200010)  /* Modem Control Register (read/write) */
-#define BTLSR		__REG(0x40200014)  /* Line Status Register (read only) */
-#define BTMSR		__REG(0x40200018)  /* Modem Status Register (read only) */
-#define BTSPR		__REG(0x4020001C)  /* Scratch Pad Register (read/write) */
-#define BTISR		__REG(0x40200020)  /* Infrared Selection Register (read/write) */
-#define BTDLL		__REG(0x40200000)  /* Divisor Latch Low Register (DLAB = 1) (read/write) */
-#define BTDLH		__REG(0x40200004)  /* Divisor Latch High Register (DLAB = 1) (read/write) */
-
-/* Standard UART (STUART) */
-#define STUART		STRBR
-#define STRBR		__REG(0x40700000)  /* Receive Buffer Register (read only) */
-#define STTHR		__REG(0x40700000)  /* Transmit Holding Register (write only) */
-#define STIER		__REG(0x40700004)  /* Interrupt Enable Register (read/write) */
-#define STIIR		__REG(0x40700008)  /* Interrupt ID Register (read only) */
-#define STFCR		__REG(0x40700008)  /* FIFO Control Register (write only) */
-#define STLCR		__REG(0x4070000C)  /* Line Control Register (read/write) */
-#define STMCR		__REG(0x40700010)  /* Modem Control Register (read/write) */
-#define STLSR		__REG(0x40700014)  /* Line Status Register (read only) */
-#define STMSR		__REG(0x40700018)  /* Reserved */
-#define STSPR		__REG(0x4070001C)  /* Scratch Pad Register (read/write) */
-#define STISR		__REG(0x40700020)  /* Infrared Selection Register (read/write) */
-#define STDLL		__REG(0x40700000)  /* Divisor Latch Low Register (DLAB = 1) (read/write) */
-#define STDLH		__REG(0x40700004)  /* Divisor Latch High Register (DLAB = 1) (read/write) */
-
-#define IER_DMAE	(1 << 7)	/* DMA Requests Enable */
-#define IER_UUE		(1 << 6)	/* UART Unit Enable */
-#define IER_NRZE	(1 << 5)	/* NRZ coding Enable */
-#define IER_RTIOE	(1 << 4)	/* Receiver Time Out Interrupt Enable */
-#define IER_MIE		(1 << 3)	/* Modem Interrupt Enable */
-#define IER_RLSE	(1 << 2)	/* Receiver Line Status Interrupt Enable */
-#define IER_TIE		(1 << 1)	/* Transmit Data request Interrupt Enable */
-#define IER_RAVIE	(1 << 0)	/* Receiver Data Available Interrupt Enable */
-
-#define IIR_FIFOES1	(1 << 7)	/* FIFO Mode Enable Status */
-#define IIR_FIFOES0	(1 << 6)	/* FIFO Mode Enable Status */
-#define IIR_TOD		(1 << 3)	/* Time Out Detected */
-#define IIR_IID2	(1 << 2)	/* Interrupt Source Encoded */
-#define IIR_IID1	(1 << 1)	/* Interrupt Source Encoded */
-#define IIR_IP		(1 << 0)	/* Interrupt Pending (active low) */
-
-#define FCR_ITL2	(1 << 7)	/* Interrupt Trigger Level */
-#define FCR_ITL1	(1 << 6)	/* Interrupt Trigger Level */
-#define FCR_RESETTF	(1 << 2)	/* Reset Transmitter FIFO */
-#define FCR_RESETRF	(1 << 1)	/* Reset Receiver FIFO */
-#define FCR_TRFIFOE	(1 << 0)	/* Transmit and Receive FIFO Enable */
-#define FCR_ITL_1	(0)
-#define FCR_ITL_8	(FCR_ITL1)
-#define FCR_ITL_16	(FCR_ITL2)
-#define FCR_ITL_32	(FCR_ITL2|FCR_ITL1)
-
-#define LCR_DLAB	(1 << 7)	/* Divisor Latch Access Bit */
-#define LCR_SB		(1 << 6)	/* Set Break */
-#define LCR_STKYP	(1 << 5)	/* Sticky Parity */
-#define LCR_EPS		(1 << 4)	/* Even Parity Select */
-#define LCR_PEN		(1 << 3)	/* Parity Enable */
-#define LCR_STB		(1 << 2)	/* Stop Bit */
-#define LCR_WLS1	(1 << 1)	/* Word Length Select */
-#define LCR_WLS0	(1 << 0)	/* Word Length Select */
-
-#define LSR_FIFOE	(1 << 7)	/* FIFO Error Status */
-#define LSR_TEMT	(1 << 6)	/* Transmitter Empty */
-#define LSR_TDRQ	(1 << 5)	/* Transmit Data Request */
-#define LSR_BI		(1 << 4)	/* Break Interrupt */
-#define LSR_FE		(1 << 3)	/* Framing Error */
-#define LSR_PE		(1 << 2)	/* Parity Error */
-#define LSR_OE		(1 << 1)	/* Overrun Error */
-#define LSR_DR		(1 << 0)	/* Data Ready */
-
-#define MCR_LOOP	(1 << 4)	*/ 
-#define MCR_OUT2	(1 << 3)	/* force MSR_DCD in loopback mode */
-#define MCR_OUT1	(1 << 2)	/* force MSR_RI in loopback mode */
-#define MCR_RTS		(1 << 1)	/* Request to Send */
-#define MCR_DTR		(1 << 0)	/* Data Terminal Ready */
-
-#define MSR_DCD		(1 << 7)	/* Data Carrier Detect */
-#define MSR_RI		(1 << 6)	/* Ring Indicator */
-#define MSR_DSR		(1 << 5)	/* Data Set Ready */
-#define MSR_CTS		(1 << 4)	/* Clear To Send */
-#define MSR_DDCD	(1 << 3)	/* Delta Data Carrier Detect */
-#define MSR_TERI	(1 << 2)	/* Trailing Edge Ring Indicator */
-#define MSR_DDSR	(1 << 1)	/* Delta Data Set Ready */
-#define MSR_DCTS	(1 << 0)	/* Delta Clear To Send */
-
-/*
- * IrSR (Infrared Selection Register)
- */
-#define IrSR_OFFSET 0x20
-
-#define IrSR_RXPL_NEG_IS_ZERO (1<<4)
-#define IrSR_RXPL_POS_IS_ZERO 0x0
-#define IrSR_TXPL_NEG_IS_ZERO (1<<3)
-#define IrSR_TXPL_POS_IS_ZERO 0x0
-#define IrSR_XMODE_PULSE_1_6  (1<<2)
-#define IrSR_XMODE_PULSE_3_16 0x0
-#define IrSR_RCVEIR_IR_MODE   (1<<1)
-#define IrSR_RCVEIR_UART_MODE 0x0
-#define IrSR_XMITIR_IR_MODE   (1<<0)
-#define IrSR_XMITIR_UART_MODE 0x0
-
-#define IrSR_IR_RECEIVE_ON (\
-                IrSR_RXPL_NEG_IS_ZERO | \
-                IrSR_TXPL_POS_IS_ZERO | \
-                IrSR_XMODE_PULSE_3_16 | \
-                IrSR_RCVEIR_IR_MODE   | \
-                IrSR_XMITIR_UART_MODE)
-
-#define IrSR_IR_TRANSMIT_ON (\
-                IrSR_RXPL_NEG_IS_ZERO | \
-                IrSR_TXPL_POS_IS_ZERO | \
-                IrSR_XMODE_PULSE_3_16 | \
-                IrSR_RCVEIR_UART_MODE | \
-                IrSR_XMITIR_IR_MODE)
-
-/*
- * I2C registers
- */
-
-#define IBMR		__REG(0x40301680)  /* I2C Bus Monitor Register - IBMR */
-#define IDBR		__REG(0x40301688)  /* I2C Data Buffer Register - IDBR */
-#define ICR		__REG(0x40301690)  /* I2C Control Register - ICR */
-#define ISR		__REG(0x40301698)  /* I2C Status Register - ISR */
-#define ISAR		__REG(0x403016A0)  /* I2C Slave Address Register - ISAR */
-
-/* ----- Control register bits ---------------------------------------- */
-
-#define ICR_START	0x1		/* start bit */
-#define ICR_STOP	0x2		/* stop bit */
-#define ICR_ACKNAK	0x4		/* send ACK(0) or NAK(1) */
-#define ICR_TB		0x8 		/* transfer byte bit */
-#define ICR_MA		0x10		/* master abort */
-#define ICR_SCLE	0x20		/* master clock enable */
-#define ICR_IUE		0x40		/* unit enable */
-#define ICR_GCD		0x80		/* general call disable */
-#define ICR_ITEIE	0x100		/* enable tx interrupts */
-#define ICR_IRFIE	0x200		/* enable rx interrupts */
-#define ICR_BEIE	0x400		/* enable bus error ints */
-#define ICR_SSDIE	0x800		/* slave STOP detected int enable */
-#define ICR_ALDIE	0x1000  	/* enable arbitration interrupt */
-#define ICR_SADIE	0x2000		/* slave address detected int enable */
-#define ICR_UR		0x4000		/* unit reset */
-#define ICR_FM		0x8000		/* Fast Mode */
-
-/* ----- Status register bits ----------------------------------------- */
-
-#define ISR_RWM         0x1		/* read/write mode */
-#define ISR_ACKNAK      0x2		/* ack/nak status */
-#define ISR_UB          0x4		/* unit busy */
-#define ISR_IBB         0x8		/* bus busy */	
-#define ISR_SSD         0x10		/* slave stop detected */
-#define ISR_ALD         0x20		/* arbitration loss detected */
-#define ISR_ITE         0x40            /* tx buffer empty */
-#define ISR_IRF         0x80            /* rx buffer full */
-#define ISR_GCAD        0x100		/* general call address detected */
-#define ISR_SAD         0x200		/* slave address detected */
-#define ISR_BED         0x400           /* bus error no ACK/NAK */
-
-/*
- * Serial Audio Controller
- */
-
-
-/* FIXME the audio defines collide w/ the SA1111 defines.  I don't like these
- * short defines because there is too much chance of namespace collision */
-
-/*#define SACR0		__REG(0x40400000)  /  Global Control Register */
-/*#define SACR1		__REG(0x40400004)  /  Serial Audio I 2 S/MSB-Justified Control Register */
-/*#define SASR0		__REG(0x4040000C)  /  Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */
-/*#define SAIMR		__REG(0x40400014)  /  Serial Audio Interrupt Mask Register */
-/*#define SAICR		__REG(0x40400018)  /  Serial Audio Interrupt Clear Register */
-/*#define SADIV		__REG(0x40400060)  /  Audio Clock Divider Register. */
-/*#define SADR		__REG(0x40400080)  /  Serial Audio Data Register (TX and RX FIFO access Register). */
-
-
-/*
- * AC97 Controller registers
- */
-
-#define POCR		__REG(0x40500000)  /* PCM Out Control Register */
-#define POCR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
-
-#define PICR		__REG(0x40500004)  /* PCM In Control Register */
-#define PICR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
-
-#define MCCR		__REG(0x40500008)  /* Mic In Control Register */
-#define MCCR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
-
-#define GCR		__REG(0x4050000C)  /* Global Control Register */
-#define GCR_CDONE_IE	(1 << 19)	/* Command Done Interrupt Enable */
-#define GCR_SDONE_IE	(1 << 18)	/* Status Done Interrupt Enable */
-#define GCR_SECRDY_IEN	(1 << 9)	/* Secondary Ready Interrupt Enable */
-#define GCR_PRIRDY_IEN	(1 << 8)	/* Primary Ready Interrupt Enable */
-#define GCR_SECRES_IEN	(1 << 5)	/* Secondary Resume Interrupt Enable */
-#define GCR_PRIRES_IEN	(1 << 4)	/* Primary Resume Interrupt Enable */
-#define GCR_ACLINK_OFF	(1 << 3)	/* AC-link Shut Off */
-#define GCR_WARM_RST	(1 << 2)	/* AC97 Warm Reset */
-#define GCR_COLD_RST	(1 << 1)	/* AC'97 Cold Reset (0 = active) */
-#define GCR_GIE		(1 << 0)	/* Codec GPI Interrupt Enable */
-
-#define POSR		__REG(0x40500010)  /* PCM Out Status Register */
-#define POSR_FIFOE	(1 << 4)	/* FIFO error */
-
-#define PISR		__REG(0x40500014)  /* PCM In Status Register */
-#define PISR_FIFOE	(1 << 4)	/* FIFO error */
-
-#define MCSR		__REG(0x40500018)  /* Mic In Status Register */
-#define MCSR_FIFOE	(1 << 4)	/* FIFO error */
-
-#define GSR		__REG(0x4050001C)  /* Global Status Register */
-#define GSR_CDONE	(1 << 19)	/* Command Done */
-#define GSR_SDONE	(1 << 18)	/* Status Done */
-#define GSR_RDCS	(1 << 15)	/* Read Completion Status */
-#define GSR_BIT3SLT12	(1 << 14)	/* Bit 3 of slot 12 */
-#define GSR_BIT2SLT12	(1 << 13)	/* Bit 2 of slot 12 */
-#define GSR_BIT1SLT12	(1 << 12)	/* Bit 1 of slot 12 */
-#define GSR_SECRES	(1 << 11)	/* Secondary Resume Interrupt */
-#define GSR_PRIRES	(1 << 10)	/* Primary Resume Interrupt */
-#define GSR_SCR		(1 << 9)	/* Secondary Codec Ready */
-#define GSR_PCR		(1 << 8)	/*  Primary Codec Ready */
-#define GSR_MINT	(1 << 7)	/* Mic In Interrupt */
-#define GSR_POINT	(1 << 6)	/* PCM Out Interrupt */
-#define GSR_PIINT	(1 << 5)	/* PCM In Interrupt */
-#define GSR_MOINT	(1 << 2)	/* Modem Out Interrupt */
-#define GSR_MIINT	(1 << 1)	/* Modem In Interrupt */
-#define GSR_GSCI	(1 << 0)	/* Codec GPI Status Change Interrupt */
-
-#define CAR		__REG(0x40500020)  /* CODEC Access Register */
-#define CAR_CAIP	(1 << 0)	/* Codec Access In Progress */
-
-#define PCDR		__REG(0x40500040)  /* PCM FIFO Data Register */
-#define MCDR		__REG(0x40500060)  /* Mic-in FIFO Data Register */
-
-#define MOCR		__REG(0x40500100)  /* Modem Out Control Register */
-#define MOCR_FEIE	(1 << 3)	/* FIFO Error */
-
-#define MICR		__REG(0x40500108)  /* Modem In Control Register */
-#define MICR_FEIE	(1 << 3)	/* FIFO Error */
-
-#define MOSR		__REG(0x40500110)  /* Modem Out Status Register */
-#define MOSR_FIFOE	(1 << 4)	/* FIFO error */
-
-#define MISR		__REG(0x40500118)  /* Modem In Status Register */
-#define MISR_FIFOE	(1 << 4)	/* FIFO error */
-
-#define MODR		__REG(0x40500140)  /* Modem FIFO Data Register */
-
-#define PAC_REG_BASE	__REG(0x40500200)  /* Primary Audio Codec */
-#define SAC_REG_BASE	__REG(0x40500300)  /* Secondary Audio Codec */
-#define PMC_REG_BASE	__REG(0x40500400)  /* Primary Modem Codec */
-#define SMC_REG_BASE	__REG(0x40500500)  /* Secondary Modem Codec */
-
-
-/*
- * USB Device Controller
- */
-#define UDC_RES1	__REG(0x40600004)  /* UDC Undocumented - Reserved1 */
-#define UDC_RES2	__REG(0x40600008)  /* UDC Undocumented - Reserved2 */
-#define UDC_RES3	__REG(0x4060000C)  /* UDC Undocumented - Reserved3 */
-
-#define UDCCR		__REG(0x40600000)  /* UDC Control Register */
-#define UDCCR_UDE	(1 << 0)	/* UDC enable */
-#define UDCCR_UDA	(1 << 1)	/* UDC active */
-#define UDCCR_RSM	(1 << 2)	/* Device resume */
-#define UDCCR_RESIR	(1 << 3)	/* Resume interrupt request */
-#define UDCCR_SUSIR	(1 << 4)	/* Suspend interrupt request */
-#define UDCCR_SRM	(1 << 5)	/* Suspend/resume interrupt mask */
-#define UDCCR_RSTIR	(1 << 6)	/* Reset interrupt request */
-#define UDCCR_REM	(1 << 7)	/* Reset interrupt mask */
-
-#define UDCCS0		__REG(0x40600010)  /* UDC Endpoint 0 Control/Status Register */
-#define UDCCS0_OPR	(1 << 0)	/* OUT packet ready */
-#define UDCCS0_IPR	(1 << 1)	/* IN packet ready */
-#define UDCCS0_FTF	(1 << 2)	/* Flush Tx FIFO */
-#define UDCCS0_DRWF	(1 << 3)	/* Device remote wakeup feature */
-#define UDCCS0_SST	(1 << 4)	/* Sent stall */
-#define UDCCS0_FST	(1 << 5)	/* Force stall */
-#define UDCCS0_RNE	(1 << 6)	/* Receive FIFO no empty */
-#define UDCCS0_SA	(1 << 7)	/* Setup active */
-
-/* Bulk IN - Endpoint 1,6,11 */
-#define UDCCS1		__REG(0x40600014)  /* UDC Endpoint 1 (IN) Control/Status Register */
-#define UDCCS6		__REG(0x40600028)  /* UDC Endpoint 6 (IN) Control/Status Register */
-#define UDCCS11		__REG(0x4060003C)  /* UDC Endpoint 11 (IN) Control/Status Register */
-
-#define UDCCS_BI_TFS	(1 << 0)	/* Transmit FIFO service */
-#define UDCCS_BI_TPC	(1 << 1)	/* Transmit packet complete */
-#define UDCCS_BI_FTF	(1 << 2)	/* Flush Tx FIFO */
-#define UDCCS_BI_TUR	(1 << 3)	/* Transmit FIFO underrun */
-#define UDCCS_BI_SST	(1 << 4)	/* Sent stall */
-#define UDCCS_BI_FST	(1 << 5)	/* Force stall */
-#define UDCCS_BI_TSP	(1 << 7)	/* Transmit short packet */
-
-/* Bulk OUT - Endpoint 2,7,12 */
-#define UDCCS2		__REG(0x40600018)  /* UDC Endpoint 2 (OUT) Control/Status Register */
-#define UDCCS7		__REG(0x4060002C)  /* UDC Endpoint 7 (OUT) Control/Status Register */
-#define UDCCS12		__REG(0x40600040)  /* UDC Endpoint 12 (OUT) Control/Status Register */
-
-#define UDCCS_BO_RFS	(1 << 0)	/* Receive FIFO service */
-#define UDCCS_BO_RPC	(1 << 1)	/* Receive packet complete */
-#define UDCCS_BO_DME	(1 << 3)	/* DMA enable */
-#define UDCCS_BO_SST	(1 << 4)	/* Sent stall */
-#define UDCCS_BO_FST	(1 << 5)	/* Force stall */
-#define UDCCS_BO_RNE	(1 << 6)	/* Receive FIFO not empty */
-#define UDCCS_BO_RSP	(1 << 7)	/* Receive short packet */
-
-/* Isochronous IN - Endpoint 3,8,13 */
-#define UDCCS3		__REG(0x4060001C)  /* UDC Endpoint 3 (IN) Control/Status Register */
-#define UDCCS8		__REG(0x40600030)  /* UDC Endpoint 8 (IN) Control/Status Register */
-#define UDCCS13		__REG(0x40600044)  /* UDC Endpoint 13 (IN) Control/Status Register */
-
-#define UDCCS_II_TFS	(1 << 0)	/* Transmit FIFO service */
-#define UDCCS_II_TPC	(1 << 1)	/* Transmit packet complete */
-#define UDCCS_II_FTF	(1 << 2)	/* Flush Tx FIFO */
-#define UDCCS_II_TUR	(1 << 3)	/* Transmit FIFO underrun */
-#define UDCCS_II_TSP	(1 << 7)	/* Transmit short packet */
-
-/* Isochronous OUT - Endpoint 4,9,14 */
-#define UDCCS4		__REG(0x40600020)  /* UDC Endpoint 4 (OUT) Control/Status Register */
-#define UDCCS9		__REG(0x40600034)  /* UDC Endpoint 9 (OUT) Control/Status Register */
-#define UDCCS14		__REG(0x40600048)  /* UDC Endpoint 14 (OUT) Control/Status Register */
-
-#define UDCCS_IO_RFS	(1 << 0)	/* Receive FIFO service */
-#define UDCCS_IO_RPC	(1 << 1)	/* Receive packet complete */
-#define UDCCS_IO_ROF	(1 << 3)	/* Receive overflow */
-#define UDCCS_IO_DME	(1 << 3)	/* DMA enable */
-#define UDCCS_IO_RNE	(1 << 6)	/* Receive FIFO not empty */
-#define UDCCS_IO_RSP	(1 << 7)	/* Receive short packet */
-
-/* Interrupt IN - Endpoint 5,10,15 */
-#define UDCCS5		__REG(0x40600024)  /* UDC Endpoint 5 (Interrupt) Control/Status Register */
-#define UDCCS10		__REG(0x40600038)  /* UDC Endpoint 10 (Interrupt) Control/Status Register */
-#define UDCCS15		__REG(0x4060004C)  /* UDC Endpoint 15 (Interrupt) Control/Status Register */
-
-#define UDCCS_INT_TFS	(1 << 0)	/* Transmit FIFO service */
-#define UDCCS_INT_TPC	(1 << 1)	/* Transmit packet complete */
-#define UDCCS_INT_FTF	(1 << 2)	/* Flush Tx FIFO */
-#define UDCCS_INT_TUR	(1 << 3)	/* Transmit FIFO underrun */
-#define UDCCS_INT_SST	(1 << 4)	/* Sent stall */
-#define UDCCS_INT_FST	(1 << 5)	/* Force stall */
-#define UDCCS_INT_TSP	(1 << 7)	/* Transmit short packet */
-
-#define UFNRH		__REG(0x40600060)  /* UDC Frame Number Register High */
-#define UFNRL		__REG(0x40600064)  /* UDC Frame Number Register Low */
-#define UBCR2		__REG(0x40600068)  /* UDC Byte Count Reg 2 */
-#define UBCR4		__REG(0x4060006c)  /* UDC Byte Count Reg 4 */
-#define UBCR7		__REG(0x40600070)  /* UDC Byte Count Reg 7 */
-#define UBCR9		__REG(0x40600074)  /* UDC Byte Count Reg 9 */
-#define UBCR12		__REG(0x40600078)  /* UDC Byte Count Reg 12 */
-#define UBCR14		__REG(0x4060007c)  /* UDC Byte Count Reg 14 */
-#define UDDR0		__REG(0x40600080)  /* UDC Endpoint 0 Data Register */
-#define UDDR1		__REG(0x40600100)  /* UDC Endpoint 1 Data Register */
-#define UDDR2		__REG(0x40600180)  /* UDC Endpoint 2 Data Register */
-#define UDDR3		__REG(0x40600200)  /* UDC Endpoint 3 Data Register */
-#define UDDR4		__REG(0x40600400)  /* UDC Endpoint 4 Data Register */
-#define UDDR5		__REG(0x406000A0)  /* UDC Endpoint 5 Data Register */
-#define UDDR6		__REG(0x40600600)  /* UDC Endpoint 6 Data Register */
-#define UDDR7		__REG(0x40600680)  /* UDC Endpoint 7 Data Register */
-#define UDDR8		__REG(0x40600700)  /* UDC Endpoint 8 Data Register */
-#define UDDR9		__REG(0x40600900)  /* UDC Endpoint 9 Data Register */
-#define UDDR10		__REG(0x406000C0)  /* UDC Endpoint 10 Data Register */
-#define UDDR11		__REG(0x40600B00)  /* UDC Endpoint 11 Data Register */
-#define UDDR12		__REG(0x40600B80)  /* UDC Endpoint 12 Data Register */
-#define UDDR13		__REG(0x40600C00)  /* UDC Endpoint 13 Data Register */
-#define UDDR14		__REG(0x40600E00)  /* UDC Endpoint 14 Data Register */
-#define UDDR15		__REG(0x406000E0)  /* UDC Endpoint 15 Data Register */
-
-#define UICR0		__REG(0x40600050)  /* UDC Interrupt Control Register 0 */
-
-#define UICR0_IM0	(1 << 0)	/* Interrupt mask ep 0 */
-#define UICR0_IM1	(1 << 1)	/* Interrupt mask ep 1 */
-#define UICR0_IM2	(1 << 2)	/* Interrupt mask ep 2 */
-#define UICR0_IM3	(1 << 3)	/* Interrupt mask ep 3 */
-#define UICR0_IM4	(1 << 4)	/* Interrupt mask ep 4 */
-#define UICR0_IM5	(1 << 5)	/* Interrupt mask ep 5 */
-#define UICR0_IM6	(1 << 6)	/* Interrupt mask ep 6 */
-#define UICR0_IM7	(1 << 7)	/* Interrupt mask ep 7 */
-
-#define UICR1		__REG(0x40600054)  /* UDC Interrupt Control Register 1 */
-
-#define UICR1_IM8	(1 << 0)	/* Interrupt mask ep 8 */
-#define UICR1_IM9	(1 << 1)	/* Interrupt mask ep 9 */
-#define UICR1_IM10	(1 << 2)	/* Interrupt mask ep 10 */
-#define UICR1_IM11	(1 << 3)	/* Interrupt mask ep 11 */
-#define UICR1_IM12	(1 << 4)	/* Interrupt mask ep 12 */
-#define UICR1_IM13	(1 << 5)	/* Interrupt mask ep 13 */
-#define UICR1_IM14	(1 << 6)	/* Interrupt mask ep 14 */
-#define UICR1_IM15	(1 << 7)	/* Interrupt mask ep 15 */
-
-#define USIR0		__REG(0x40600058)  /* UDC Status Interrupt Register 0 */
-
-#define USIR0_IR0	(1 << 0)	/* Interrup request ep 0 */
-#define USIR0_IR1	(1 << 1)	/* Interrup request ep 1 */
-#define USIR0_IR2	(1 << 2)	/* Interrup request ep 2 */
-#define USIR0_IR3	(1 << 3)	/* Interrup request ep 3 */
-#define USIR0_IR4	(1 << 4)	/* Interrup request ep 4 */
-#define USIR0_IR5	(1 << 5)	/* Interrup request ep 5 */
-#define USIR0_IR6	(1 << 6)	/* Interrup request ep 6 */
-#define USIR0_IR7	(1 << 7)	/* Interrup request ep 7 */
-
-#define USIR1		__REG(0x4060005C)  /* UDC Status Interrupt Register 1 */
-
-#define USIR1_IR8	(1 << 0)	/* Interrup request ep 8 */
-#define USIR1_IR9	(1 << 1)	/* Interrup request ep 9 */
-#define USIR1_IR10	(1 << 2)	/* Interrup request ep 10 */
-#define USIR1_IR11	(1 << 3)	/* Interrup request ep 11 */
-#define USIR1_IR12	(1 << 4)	/* Interrup request ep 12 */
-#define USIR1_IR13	(1 << 5)	/* Interrup request ep 13 */
-#define USIR1_IR14	(1 << 6)	/* Interrup request ep 14 */
-#define USIR1_IR15	(1 << 7)	/* Interrup request ep 15 */
-
-
-/*
- * Fast Infrared Communication Port
- */
-
-#define ICCR0		__REG(0x40800000)  /* ICP Control Register 0 */
-#define ICCR1		__REG(0x40800004)  /* ICP Control Register 1 */
-#define ICCR2		__REG(0x40800008)  /* ICP Control Register 2 */
-#define ICDR		__REG(0x4080000c)  /* ICP Data Register */
-#define ICSR0		__REG(0x40800014)  /* ICP Status Register 0 */
-#define ICSR1		__REG(0x40800018)  /* ICP Status Register 1 */
-
-
-/*
- * Real Time Clock
- */
-
-#define RCNR		__REG(0x40900000)  /* RTC Count Register */
-#define RTAR		__REG(0x40900004)  /* RTC Alarm Register */
-#define RTSR		__REG(0x40900008)  /* RTC Status Register */
-#define RTTR		__REG(0x4090000C)  /* RTC Timer Trim Register */
-
-#define RTSR_HZE	(1 << 3)	/* HZ interrupt enable */
-#define RTSR_ALE	(1 << 2)	/* RTC alarm interrupt enable */
-#define RTSR_HZ		(1 << 1)	/* HZ rising-edge detected */
-#define RTSR_AL		(1 << 0)	/* RTC alarm detected */
-
-
-/*
- * OS Timer & Match Registers
- */
-
-#define OSMR0		__REG(0x40A00000)  /* */
-#define OSMR1		__REG(0x40A00004)  /* */
-#define OSMR2		__REG(0x40A00008)  /* */
-#define OSMR3		__REG(0x40A0000C)  /* */
-#define OSCR		__REG(0x40A00010)  /* OS Timer Counter Register */
-#define OSSR		__REG(0x40A00014)  /* OS Timer Status Register */
-#define OWER		__REG(0x40A00018)  /* OS Timer Watchdog Enable Register */
-#define OIER		__REG(0x40A0001C)  /* OS Timer Interrupt Enable Register */
-
-#define OSSR_M3		(1 << 3)	/* Match status channel 3 */
-#define OSSR_M2		(1 << 2)	/* Match status channel 2 */
-#define OSSR_M1		(1 << 1)	/* Match status channel 1 */
-#define OSSR_M0		(1 << 0)	/* Match status channel 0 */
-
-#define OWER_WME	(1 << 0)	/* Watchdog Match Enable */
-
-#define OIER_E3		(1 << 3)	/* Interrupt enable channel 3 */
-#define OIER_E2		(1 << 2)	/* Interrupt enable channel 2 */
-#define OIER_E1		(1 << 1)	/* Interrupt enable channel 1 */
-#define OIER_E0		(1 << 0)	/* Interrupt enable channel 0 */
-
-
-/*
- * Pulse Width Modulator
- */
-
-#define PWM_CTRL0	__REG(0x40B00000)  /* PWM 0 Control Register */
-#define PWM_PWDUTY0	__REG(0x40B00004)  /* PWM 0 Duty Cycle Register */
-#define PWM_PERVAL0	__REG(0x40B00008)  /* PWM 0 Period Control Register */
-
-#define PWM_CTRL1	__REG(0x40C00000)  /* PWM 1Control Register */
-#define PWM_PWDUTY1	__REG(0x40C00004)  /* PWM 1 Duty Cycle Register */
-#define PWM_PERVAL1	__REG(0x40C00008)  /* PWM 1 Period Control Register */
-
-
-/*
- * Interrupt Controller
- */
-
-#define ICIP		__REG(0x40D00000)  /* Interrupt Controller IRQ Pending Register */
-#define ICMR		__REG(0x40D00004)  /* Interrupt Controller Mask Register */
-#define ICLR		__REG(0x40D00008)  /* Interrupt Controller Level Register */
-#define ICFP		__REG(0x40D0000C)  /* Interrupt Controller FIQ Pending Register */
-#define ICPR		__REG(0x40D00010)  /* Interrupt Controller Pending Register */
-#define ICCR		__REG(0x40D00014)  /* Interrupt Controller Control Register */
-
-
-/*
- * General Purpose I/O
- */
-
-#define GPLR0		__REG(0x40E00000)  /* GPIO Pin-Level Register GPIO<31:0> */
-#define GPLR1		__REG(0x40E00004)  /* GPIO Pin-Level Register GPIO<63:32> */
-#define GPLR2		__REG(0x40E00008)  /* GPIO Pin-Level Register GPIO<80:64> */
-
-#define GPDR0		__REG(0x40E0000C)  /* GPIO Pin Direction Register GPIO<31:0> */
-#define GPDR1		__REG(0x40E00010)  /* GPIO Pin Direction Register GPIO<63:32> */
-#define GPDR2		__REG(0x40E00014)  /* GPIO Pin Direction Register GPIO<80:64> */
-
-#define GPSR0		__REG(0x40E00018)  /* GPIO Pin Output Set Register GPIO<31:0> */
-#define GPSR1		__REG(0x40E0001C)  /* GPIO Pin Output Set Register GPIO<63:32> */
-#define GPSR2		__REG(0x40E00020)  /* GPIO Pin Output Set Register GPIO<80:64> */
-
-#define GPCR0		__REG(0x40E00024)  /* GPIO Pin Output Clear Register GPIO<31:0> */
-#define GPCR1		__REG(0x40E00028)  /* GPIO Pin Output Clear Register GPIO <63:32> */
-#define GPCR2		__REG(0x40E0002C)  /* GPIO Pin Output Clear Register GPIO <80:64> */
-
-#define GRER0		__REG(0x40E00030)  /* GPIO Rising-Edge Detect Register GPIO<31:0> */
-#define GRER1		__REG(0x40E00034)  /* GPIO Rising-Edge Detect Register GPIO<63:32> */
-#define GRER2		__REG(0x40E00038)  /* GPIO Rising-Edge Detect Register GPIO<80:64> */
-
-#define GFER0		__REG(0x40E0003C)  /* GPIO Falling-Edge Detect Register GPIO<31:0> */
-#define GFER1		__REG(0x40E00040)  /* GPIO Falling-Edge Detect Register GPIO<63:32> */
-#define GFER2		__REG(0x40E00044)  /* GPIO Falling-Edge Detect Register GPIO<80:64> */
-
-#define GEDR0		__REG(0x40E00048)  /* GPIO Edge Detect Status Register GPIO<31:0> */
-#define GEDR1		__REG(0x40E0004C)  /* GPIO Edge Detect Status Register GPIO<63:32> */
-#define GEDR2		__REG(0x40E00050)  /* GPIO Edge Detect Status Register GPIO<80:64> */
-
-#define GAFR0_L		__REG(0x40E00054)  /* GPIO Alternate Function Select Register GPIO<15:0> */
-#define GAFR0_U		__REG(0x40E00058)  /* GPIO Alternate Function Select Register GPIO<31:16> */
-#define GAFR1_L		__REG(0x40E0005C)  /* GPIO Alternate Function Select Register GPIO<47:32> */
-#define GAFR1_U		__REG(0x40E00060)  /* GPIO Alternate Function Select Register GPIO<63:48> */
-#define GAFR2_L		__REG(0x40E00064)  /* GPIO Alternate Function Select Register GPIO<79:64> */
-#define GAFR2_U		__REG(0x40E00068)  /* GPIO Alternate Function Select Register GPIO 80 */
-
-/* More handy macros.  The argument is a literal GPIO number. */
-
-#define GPIO_bit(x)	(1 << ((x) & 0x1f))
-#define GPLR(x)		__REG2(0x40E00000, ((x) & 0x60) >> 3)
-#define GPDR(x)		__REG2(0x40E0000C, ((x) & 0x60) >> 3)
-#define GPSR(x)		__REG2(0x40E00018, ((x) & 0x60) >> 3)
-#define GPCR(x)		__REG2(0x40E00024, ((x) & 0x60) >> 3)
-#define GRER(x)		__REG2(0x40E00030, ((x) & 0x60) >> 3)
-#define GFER(x)		__REG2(0x40E0003C, ((x) & 0x60) >> 3)
-#define GEDR(x)		__REG2(0x40E00048, ((x) & 0x60) >> 3)
-#define GAFR(x)		__REG2(0x40E00054, ((x) & 0x70) >> 2)
-
-/* GPIO alternate function assignments */
-
-#define GPIO1_RST		1	/* reset */
-#define GPIO6_MMCCLK		6	/* MMC Clock */
-#define GPIO8_48MHz		7	/* 48 MHz clock output */
-#define GPIO8_MMCCS0		8	/* MMC Chip Select 0 */
-#define GPIO9_MMCCS1		9	/* MMC Chip Select 1 */
-#define GPIO10_RTCCLK		10	/* real time clock (1 Hz) */
-#define GPIO11_3_6MHz		11	/* 3.6 MHz oscillator out */
-#define GPIO12_32KHz		12	/* 32 kHz out */
-#define GPIO13_MBGNT		13	/* memory controller grant */
-#define GPIO14_MBREQ		14	/* alternate bus master request */
-#define GPIO15_nCS_1		15	/* chip select 1 */
-#define GPIO16_PWM0		16	/* PWM0 output */
-#define GPIO17_PWM1		17	/* PWM1 output */
-#define GPIO18_RDY		18	/* Ext. Bus Ready */
-#define GPIO19_DREQ1		19	/* External DMA Request */
-#define GPIO20_DREQ0		20	/* External DMA Request */
-#define GPIO23_SCLK		23	/* SSP clock */
-#define GPIO24_SFRM		24	/* SSP Frame */
-#define GPIO25_STXD		25	/* SSP transmit */
-#define GPIO26_SRXD		26	/* SSP receive */
-#define GPIO27_SEXTCLK		27	/* SSP ext_clk */
-#define GPIO28_BITCLK		28	/* AC97/I2S bit_clk */
-#define GPIO29_SDATA_IN		29	/* AC97 Sdata_in0 / I2S Sdata_in */
-#define GPIO30_SDATA_OUT	30	/* AC97/I2S Sdata_out */
-#define GPIO31_SYNC		31	/* AC97/I2S sync */
-#define GPIO32_SDATA_IN1	32	/* AC97 Sdata_in1 */
-#define GPIO33_nCS_5		33	/* chip select 5 */
-#define GPIO34_FFRXD		34	/* FFUART receive */
-#define GPIO34_MMCCS0		34	/* MMC Chip Select 0 */
-#define GPIO35_FFCTS		35	/* FFUART Clear to send */
-#define GPIO36_FFDCD		36	/* FFUART Data carrier detect */
-#define GPIO37_FFDSR		37	/* FFUART data set ready */
-#define GPIO38_FFRI		38	/* FFUART Ring Indicator */
-#define GPIO39_MMCCS1		39	/* MMC Chip Select 1 */
-#define GPIO39_FFTXD		39	/* FFUART transmit data */
-#define GPIO40_FFDTR		40	/* FFUART data terminal Ready */
-#define GPIO41_FFRTS		41	/* FFUART request to send */
-#define GPIO42_BTRXD		42	/* BTUART receive data */
-#define GPIO43_BTTXD		43	/* BTUART transmit data */
-#define GPIO44_BTCTS		44	/* BTUART clear to send */
-#define GPIO45_BTRTS		45	/* BTUART request to send */
-#define GPIO46_ICPRXD		46	/* ICP receive data */
-#define GPIO46_STRXD		46	/* STD_UART receive data */
-#define GPIO47_ICPTXD		47	/* ICP transmit data */
-#define GPIO47_STTXD		47	/* STD_UART transmit data */
-#define GPIO48_nPOE		48	/* Output Enable for Card Space */
-#define GPIO49_nPWE		49	/* Write Enable for Card Space */
-#define GPIO50_nPIOR		50	/* I/O Read for Card Space */
-#define GPIO51_nPIOW		51	/* I/O Write for Card Space */
-#define GPIO52_nPCE_1		52	/* Card Enable for Card Space */
-#define GPIO53_nPCE_2		53	/* Card Enable for Card Space */
-#define GPIO53_MMCCLK		53	/* MMC Clock */
-#define GPIO54_MMCCLK		54	/* MMC Clock */
-#define GPIO54_pSKTSEL		54	/* Socket Select for Card Space */
-#define GPIO55_nPREG		55	/* Card Address bit 26 */
-#define GPIO56_nPWAIT		56	/* Wait signal for Card Space */
-#define GPIO57_nIOIS16		57	/* Bus Width select for I/O Card Space */
-#define GPIO58_LDD_0		58	/* LCD data pin 0 */
-#define GPIO59_LDD_1		59	/* LCD data pin 1 */
-#define GPIO60_LDD_2		60	/* LCD data pin 2 */
-#define GPIO61_LDD_3		61	/* LCD data pin 3 */
-#define GPIO62_LDD_4		62	/* LCD data pin 4 */
-#define GPIO63_LDD_5		63	/* LCD data pin 5 */
-#define GPIO64_LDD_6		64	/* LCD data pin 6 */
-#define GPIO65_LDD_7		65	/* LCD data pin 7 */
-#define GPIO66_LDD_8		66	/* LCD data pin 8 */
-#define GPIO66_MBREQ		66	/* alternate bus master req */
-#define GPIO67_LDD_9		67	/* LCD data pin 9 */
-#define GPIO67_MMCCS0		67	/* MMC Chip Select 0 */
-#define GPIO68_LDD_10		68	/* LCD data pin 10 */
-#define GPIO68_MMCCS1		68	/* MMC Chip Select 1 */
-#define GPIO69_LDD_11		69	/* LCD data pin 11 */
-#define GPIO69_MMCCLK		69	/* MMC_CLK */
-#define GPIO70_LDD_12		70	/* LCD data pin 12 */
-#define GPIO70_RTCCLK		70	/* Real Time clock (1 Hz) */
-#define GPIO71_LDD_13		71	/* LCD data pin 13 */
-#define GPIO71_3_6MHz		71	/* 3.6 MHz Oscillator clock */
-#define GPIO72_LDD_14		72	/* LCD data pin 14 */
-#define GPIO72_32kHz		72	/* 32 kHz clock */
-#define GPIO73_LDD_15		73	/* LCD data pin 15 */
-#define GPIO73_MBGNT		73	/* Memory controller grant */
-#define GPIO74_LCD_FCLK		74	/* LCD Frame clock */
-#define GPIO75_LCD_LCLK		75	/* LCD line clock */
-#define GPIO76_LCD_PCLK		76	/* LCD Pixel clock */
-#define GPIO77_LCD_ACBIAS	77	/* LCD AC Bias */
-#define GPIO78_nCS_2		78	/* chip select 2 */
-#define GPIO79_nCS_3		79	/* chip select 3 */
-#define GPIO80_nCS_4		80	/* chip select 4 */
-
-/* GPIO alternate function mode & direction */
-
-#define GPIO_IN			0x000
-#define GPIO_OUT		0x080
-#define GPIO_ALT_FN_1_IN	0x100
-#define GPIO_ALT_FN_1_OUT	0x180
-#define GPIO_ALT_FN_2_IN	0x200
-#define GPIO_ALT_FN_2_OUT	0x280
-#define GPIO_ALT_FN_3_IN	0x300
-#define GPIO_ALT_FN_3_OUT	0x380
-#define GPIO_MD_MASK_NR		0x07f
-#define GPIO_MD_MASK_DIR	0x080
-#define GPIO_MD_MASK_FN		0x300
-
-#define GPIO1_RTS_MD		( 1 | GPIO_ALT_FN_1_IN)
-#define GPIO6_MMCCLK_MD		( 6 | GPIO_ALT_FN_1_OUT)
-#define GPIO8_48MHz_MD		( 8 | GPIO_ALT_FN_1_OUT)
-#define GPIO8_MMCCS0_MD		( 8 | GPIO_ALT_FN_1_OUT)
-#define GPIO9_MMCCS1_MD		( 9 | GPIO_ALT_FN_1_OUT)
-#define GPIO10_RTCCLK_MD	(10 | GPIO_ALT_FN_1_OUT)
-#define GPIO11_3_6MHz_MD	(11 | GPIO_ALT_FN_1_OUT)
-#define GPIO12_32KHz_MD		(12 | GPIO_ALT_FN_1_OUT)
-#define GPIO13_MBGNT_MD		(13 | GPIO_ALT_FN_2_OUT)
-#define GPIO14_MBREQ_MD		(14 | GPIO_ALT_FN_1_IN)
-#define GPIO15_nCS_1_MD		(15 | GPIO_ALT_FN_2_OUT)
-#define GPIO16_PWM0_MD		(16 | GPIO_ALT_FN_2_OUT)
-#define GPIO17_PWM1_MD		(17 | GPIO_ALT_FN_2_OUT)
-#define GPIO18_RDY_MD		(18 | GPIO_ALT_FN_1_IN)
-#define GPIO19_DREQ1_MD		(19 | GPIO_ALT_FN_1_IN)
-#define GPIO20_DREQ0_MD		(20 | GPIO_ALT_FN_1_IN)
-#define GPIO23_SCLK_md		(23 | GPIO_ALT_FN_2_OUT)
-#define GPIO24_SFRM_MD		(24 | GPIO_ALT_FN_2_OUT)
-#define GPIO25_STXD_MD		(25 | GPIO_ALT_FN_2_OUT)
-#define GPIO26_SRXD_MD		(26 | GPIO_ALT_FN_1_IN)
-#define GPIO27_SEXTCLK_MD	(27 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_AC97_MD	(28 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_I2S_MD	(28 | GPIO_ALT_FN_2_IN)
-#define GPIO29_SDATA_IN_AC97_MD	(29 | GPIO_ALT_FN_1_IN)
-#define GPIO29_SDATA_IN_I2S_MD	(29 | GPIO_ALT_FN_2_IN)
-#define GPIO30_SDATA_OUT_AC97_MD	(30 | GPIO_ALT_FN_2_OUT)
-#define GPIO30_SDATA_OUT_I2S_MD	(30 | GPIO_ALT_FN_1_OUT)
-#define GPIO31_SYNC_AC97_MD	(31 | GPIO_ALT_FN_2_OUT)
-#define GPIO31_SYNC_I2S_MD	(31 | GPIO_ALT_FN_1_OUT)
-#define GPIO32_SDATA_IN1_AC97_MD	(32 | GPIO_ALT_FN_1_IN)
-#define GPIO33_nCS_5_MD		(33 | GPIO_ALT_FN_2_OUT)
-#define GPIO34_FFRXD_MD		(34 | GPIO_ALT_FN_1_IN)
-#define GPIO34_MMCCS0_MD	(34 | GPIO_ALT_FN_2_OUT)
-#define GPIO35_FFCTS_MD		(35 | GPIO_ALT_FN_1_IN)
-#define GPIO36_FFDCD_MD		(36 | GPIO_ALT_FN_1_IN)
-#define GPIO37_FFDSR_MD		(37 | GPIO_ALT_FN_1_IN)
-#define GPIO38_FFRI_MD		(38 | GPIO_ALT_FN_1_IN)
-#define GPIO39_MMCCS1_MD	(39 | GPIO_ALT_FN_1_OUT)
-#define GPIO39_FFTXD_MD		(39 | GPIO_ALT_FN_2_OUT)
-#define GPIO40_FFDTR_MD		(40 | GPIO_ALT_FN_2_OUT)
-#define GPIO41_FFRTS_MD		(41 | GPIO_ALT_FN_2_OUT)
-#define GPIO42_BTRXD_MD		(42 | GPIO_ALT_FN_1_IN)
-#define GPIO43_BTTXD_MD		(43 | GPIO_ALT_FN_2_OUT)
-#define GPIO44_BTCTS_MD		(44 | GPIO_ALT_FN_1_IN)
-#define GPIO45_BTRTS_MD		(45 | GPIO_ALT_FN_2_OUT)
-#define GPIO46_ICPRXD_MD	(46 | GPIO_ALT_FN_1_IN)
-#define GPIO46_STRXD_MD		(46 | GPIO_ALT_FN_2_IN)
-#define GPIO47_ICPTXD_MD	(47 | GPIO_ALT_FN_2_OUT)
-#define GPIO47_STTXD_MD		(47 | GPIO_ALT_FN_1_OUT)
-#define GPIO48_nPOE_MD		(48 | GPIO_ALT_FN_2_OUT)
-#define GPIO49_nPWE_MD		(49 | GPIO_ALT_FN_2_OUT)
-#define GPIO50_nPIOR_MD		(50 | GPIO_ALT_FN_2_OUT)
-#define GPIO51_nPIOW_MD		(51 | GPIO_ALT_FN_2_OUT)
-#define GPIO52_nPCE_1_MD	(52 | GPIO_ALT_FN_2_OUT)
-#define GPIO53_nPCE_2_MD	(53 | GPIO_ALT_FN_2_OUT)
-#define GPIO53_MMCCLK_MD	(53 | GPIO_ALT_FN_1_OUT)
-#define GPIO54_MMCCLK_MD	(54 | GPIO_ALT_FN_1_OUT)
-#define GPIO54_pSKTSEL_MD	(54 | GPIO_ALT_FN_2_OUT)
-#define GPIO55_nPREG_MD		(55 | GPIO_ALT_FN_2_OUT)
-#define GPIO56_nPWAIT_MD	(56 | GPIO_ALT_FN_1_IN)
-#define GPIO57_nIOIS16_MD	(57 | GPIO_ALT_FN_1_IN)
-#define GPIO58_LDD_0_MD		(58 | GPIO_ALT_FN_2_OUT)
-#define GPIO59_LDD_1_MD		(59 | GPIO_ALT_FN_2_OUT)
-#define GPIO60_LDD_2_MD		(60 | GPIO_ALT_FN_2_OUT)
-#define GPIO61_LDD_3_MD		(61 | GPIO_ALT_FN_2_OUT)
-#define GPIO62_LDD_4_MD		(62 | GPIO_ALT_FN_2_OUT)
-#define GPIO63_LDD_5_MD		(63 | GPIO_ALT_FN_2_OUT)
-#define GPIO64_LDD_6_MD		(64 | GPIO_ALT_FN_2_OUT)
-#define GPIO65_LDD_7_MD		(65 | GPIO_ALT_FN_2_OUT)
-#define GPIO66_LDD_8_MD		(66 | GPIO_ALT_FN_2_OUT)
-#define GPIO66_MBREQ_MD		(66 | GPIO_ALT_FN_1_IN)
-#define GPIO67_LDD_9_MD		(67 | GPIO_ALT_FN_2_OUT)
-#define GPIO67_MMCCS0_MD	(67 | GPIO_ALT_FN_1_OUT)
-#define GPIO68_LDD_10_MD	(68 | GPIO_ALT_FN_2_OUT)
-#define GPIO68_MMCCS1_MD	(68 | GPIO_ALT_FN_1_OUT)
-#define GPIO69_LDD_11_MD	(69 | GPIO_ALT_FN_2_OUT)
-#define GPIO69_MMCCLK_MD	(69 | GPIO_ALT_FN_1_OUT)
-#define GPIO70_LDD_12_MD	(70 | GPIO_ALT_FN_2_OUT)
-#define GPIO70_RTCCLK_MD	(70 | GPIO_ALT_FN_1_OUT)
-#define GPIO71_LDD_13_MD	(71 | GPIO_ALT_FN_2_OUT)
-#define GPIO71_3_6MHz_MD	(71 | GPIO_ALT_FN_1_OUT)
-#define GPIO72_LDD_14_MD	(72 | GPIO_ALT_FN_2_OUT)
-#define GPIO72_32kHz_MD		(72 | GPIO_ALT_FN_1_OUT)
-#define GPIO73_LDD_15_MD	(73 | GPIO_ALT_FN_2_OUT)
-#define GPIO73_MBGNT_MD		(73 | GPIO_ALT_FN_1_OUT)
-#define GPIO74_LCD_FCLK_MD	(74 | GPIO_ALT_FN_2_OUT)
-#define GPIO75_LCD_LCLK_MD	(75 | GPIO_ALT_FN_2_OUT)
-#define GPIO76_LCD_PCLK_MD	(76 | GPIO_ALT_FN_2_OUT)
-#define GPIO77_LCD_ACBIAS_MD	(77 | GPIO_ALT_FN_2_OUT)
-#define GPIO78_nCS_2_MD		(78 | GPIO_ALT_FN_2_OUT)
-#define GPIO79_nCS_3_MD		(79 | GPIO_ALT_FN_2_OUT)
-#define GPIO80_nCS_4_MD		(80 | GPIO_ALT_FN_2_OUT)
-
-
-/*
- * Power Manager
- */
-
-#define PMCR		__REG(0x40F00000)  /* Power Manager Control Register */
-#define PSSR		__REG(0x40F00004)  /* Power Manager Sleep Status Register */
-#define PSPR		__REG(0x40F00008)  /* Power Manager Scratch Pad Register */
-#define PWER		__REG(0x40F0000C)  /* Power Manager Wake-up Enable Register */
-#define PRER		__REG(0x40F00010)  /* Power Manager GPIO Rising-Edge Detect Enable Register */
-#define PFER		__REG(0x40F00014)  /* Power Manager GPIO Falling-Edge Detect Enable Register */
-#define PEDR		__REG(0x40F00018)  /* Power Manager GPIO Edge Detect Status Register */
-#define PCFR		__REG(0x40F0001C)  /* Power Manager General Configuration Register */
-#define PGSR0		__REG(0x40F00020)  /* Power Manager GPIO Sleep State Register for GP[31-0] */
-#define PGSR1		__REG(0x40F00024)  /* Power Manager GPIO Sleep State Register for GP[63-32] */
-#define PGSR2		__REG(0x40F00028)  /* Power Manager GPIO Sleep State Register for GP[84-64] */
-#define RCSR		__REG(0x40F00030)  /* Reset Controller Status Register */
-
-#define PSSR_RDH	(1 << 5)	/* Read Disable Hold */
-#define PSSR_PH		(1 << 4)	/* Peripheral Control Hold */
-#define PSSR_VFS	(1 << 2)	/* VDD Fault Status */
-#define PSSR_BFS	(1 << 1)	/* Battery Fault Status */
-#define PSSR_SSS	(1 << 0)	/* Software Sleep Status */
-
-#define PCFR_DS		(1 << 3)	/* Deep Sleep Mode */
-#define PCFR_FS		(1 << 2)	/* Float Static Chip Selects */
-#define PCFR_FP		(1 << 1)	/* Float PCMCIA controls */
-#define PCFR_OPDE	(1 << 0)	/* 3.6864 MHz oscillator power-down enable */
-
-#define RCSR_GPR	(1 << 3)	/* GPIO Reset */
-#define RCSR_SMR	(1 << 2)	/* Sleep Mode */
-#define RCSR_WDR	(1 << 1)	/* Watchdog Reset */
-#define RCSR_HWR	(1 << 0)	/* Hardware Reset */
-
-
-/*
- * SSP Serial Port Registers
- */
-
-#define SSCR0		__REG(0x41000000)  /* SSP Control Register 0 */
-#define SSCR1		__REG(0x41000004)  /* SSP Control Register 1 */
-#define SSSR		__REG(0x41000008)  /* SSP Status Register */
-#define SSITR		__REG(0x4100000C)  /* SSP Interrupt Test Register */
-#define SSDR		__REG(0x41000010)  /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
-
-
-/*
- * MultiMediaCard (MMC) controller
- */
-
-#define MMC_STRPCL	__REG(0x41100000)  /* Control to start and stop MMC clock */
-#define MMC_STAT	__REG(0x41100004)  /* MMC Status Register (read only) */
-#define MMC_CLKRT	__REG(0x41100008)  /* MMC clock rate */
-#define MMC_SPI		__REG(0x4110000c)  /* SPI mode control bits */
-#define MMC_CMDAT	__REG(0x41100010)  /* Command/response/data sequence control */
-#define MMC_RESTO	__REG(0x41100014)  /* Expected response time out */
-#define MMC_RDTO	__REG(0x41100018)  /* Expected data read time out */
-#define MMC_BLKLEN	__REG(0x4110001c)  /* Block length of data transaction */
-#define MMC_NOB		__REG(0x41100020)  /* Number of blocks, for block mode */
-#define MMC_PRTBUF	__REG(0x41100024)  /* Partial MMC_TXFIFO FIFO written */
-#define MMC_I_MASK	__REG(0x41100028)  /* Interrupt Mask */
-#define MMC_I_REG	__REG(0x4110002c)  /* Interrupt Register (read only) */
-#define MMC_CMD		__REG(0x41100030)  /* Index of current command */
-#define MMC_ARGH	__REG(0x41100034)  /* MSW part of the current command argument */
-#define MMC_ARGL	__REG(0x41100038)  /* LSW part of the current command argument */
-#define MMC_RES		__REG(0x4110003c)  /* Response FIFO (read only) */
-#define MMC_RXFIFO	__REG(0x41100040)  /* Receive FIFO (read only) */
-#define MMC_TXFIFO	__REG(0x41100044)  /* Transmit FIFO (write only) */
-
-
-/*
- * Core Clock
- */
-
-#define CCCR		__REG(0x41300000)  /* Core Clock Configuration Register */
-#define CKEN		__REG(0x41300004)  /* Clock Enable Register */
-#define OSCC		__REG(0x41300008)  /* Oscillator Configuration Register */
-
-#define CCCR_N_MASK	0x0380		/* Run Mode Frequency to Turbo Mode Frequency Multiplier */
-#define CCCR_M_MASK	0x0060		/* Memory Frequency to Run Mode Frequency Multiplier */
-#define CCCR_L_MASK	0x001f		/* Crystal Frequency to Memory Frequency Multiplier */
-
-#define CKEN16_LCD	(1 << 16)	/* LCD Unit Clock Enable */
-#define CKEN14_I2C	(1 << 14)	/* I2C Unit Clock Enable */
-#define CKEN13_FICP	(1 << 13)	/* FICP Unit Clock Enable */
-#define CKEN12_MMC	(1 << 12)	/* MMC Unit Clock Enable */
-#define CKEN11_USB	(1 << 11)	/* USB Unit Clock Enable */
-#define CKEN8_I2S	(1 << 8)	/* I2S Unit Clock Enable */
-#define CKEN7_BTUART	(1 << 7)	/* BTUART Unit Clock Enable */
-#define CKEN6_FFUART	(1 << 6)	/* FFUART Unit Clock Enable */
-#define CKEN5_STUART	(1 << 5)	/* STUART Unit Clock Enable */
-#define CKEN3_SSP	(1 << 3)	/* SSP Unit Clock Enable */
-#define CKEN2_AC97	(1 << 2)	/* AC97 Unit Clock Enable */
-#define CKEN1_PWM1	(1 << 1)	/* PWM1 Clock Enable */
-#define CKEN0_PWM0	(1 << 0)	/* PWM0 Clock Enable */
-
-#define OSCC_OON	(1 << 1)	/* 32.768kHz OON (write-once only bit) */
-#define OSCC_OOK	(1 << 0)	/* 32.768kHz OOK (read-only bit) */
-
-#define  CCCR_L09      (0x1F)
-#define  CCCR_L27      (0x1)
-#define  CCCR_L32      (0x2)
-#define  CCCR_L36      (0x3)
-#define  CCCR_L40      (0x4)
-#define  CCCR_L45      (0x5)
-
-#define  CCCR_M1       (0x1 << 5)
-#define  CCCR_M2       (0x2 << 5)
-#define  CCCR_M4       (0x3 << 5)
-
-#define  CCCR_N10      (0x2 << 7)
-#define  CCCR_N15      (0x3 << 7)
-#define  CCCR_N20      (0x4 << 7)
-#define  CCCR_N25      (0x5 << 7)
-#define  CCCR_N30      (0x6 << 7)
-
-/*
- * LCD
- */
-
-#define LCCR0		__REG(0x44000000)  /* LCD Controller Control Register 0 */
-#define LCCR1		__REG(0x44000004)  /* LCD Controller Control Register 1 */
-#define LCCR2		__REG(0x44000008)  /* LCD Controller Control Register 2 */
-#define LCCR3		__REG(0x4400000C)  /* LCD Controller Control Register 3 */
-#define DFBR0		__REG(0x44000020)  /* DMA Channel 0 Frame Branch Register */
-#define DFBR1		__REG(0x44000024)  /* DMA Channel 1 Frame Branch Register */
-#define LCSR		__REG(0x44000038)  /* LCD Controller Status Register */
-#define LIIDR		__REG(0x4400003C)  /* LCD Controller Interrupt ID Register */
-#define TMEDRGBR	__REG(0x44000040)  /* TMED RGB Seed Register */
-#define TMEDCR		__REG(0x44000044)  /* TMED Control Register */
-
-#define FDADR0		__REG(0x44000200)  /* DMA Channel 0 Frame Descriptor Address Register */
-#define FSADR0		__REG(0x44000204)  /* DMA Channel 0 Frame Source Address Register */
-#define FIDR0		__REG(0x44000208)  /* DMA Channel 0 Frame ID Register */
-#define LDCMD0		__REG(0x4400020C)  /* DMA Channel 0 Command Register */
-#define FDADR1		__REG(0x44000210)  /* DMA Channel 1 Frame Descriptor Address Register */
-#define FSADR1		__REG(0x44000214)  /* DMA Channel 1 Frame Source Address Register */
-#define FIDR1		__REG(0x44000218)  /* DMA Channel 1 Frame ID Register */
-#define LDCMD1		__REG(0x4400021C)  /* DMA Channel 1 Command Register */
-
-#define LCCR0_ENB	(1 << 0)	/* LCD Controller enable */
-#define LCCR0_CMS	(1 << 1)	/* Color = 0, Monochrome = 1 */
-#define LCCR0_SDS	(1 << 2)	/* Single Panel = 0, Dual Panel = 1 */
-#define LCCR0_LDM	(1 << 3)	/* LCD Disable Done Mask */
-#define LCCR0_SFM	(1 << 4)	/* Start of frame mask */
-#define LCCR0_IUM	(1 << 5)	/* Input FIFO underrun mask */
-#define LCCR0_EFM	(1 << 6)	/* End of Frame mask */
-#define LCCR0_PAS	(1 << 7)	/* Passive = 0, Active = 1 */
-#define LCCR0_BLE	(1 << 8)	/* Little Endian = 0, Big Endian = 1 */
-#define LCCR0_DPD	(1 << 9)	/* Double Pixel mode, 4 pixel value = 0, 8 pixle values = 1 */
-#define LCCR0_DIS	(1 << 10)	/* LCD Disable */
-#define LCCR0_QDM	(1 << 11)	/* LCD Quick Disable mask */
-#define LCCR0_PDD	(0xff << 12)	/* Palette DMA request delay */
-#define LCCR0_PDD_S	12
-#define LCCR0_BM	(1 << 20) 	/* Branch mask */
-#define LCCR0_OUM	(1 << 21)	/* Output FIFO underrun mask */
-
-#define LCCR1_PPL       Fld (10, 0)      /* Pixels Per Line - 1 */
-#define LCCR1_DisWdth(Pixel)            /* Display Width [1..800 pix.]  */ \
-                        (((Pixel) - 1) << FShft (LCCR1_PPL))
-
-#define LCCR1_HSW       Fld (6, 10)     /* Horizontal Synchronization     */
-#define LCCR1_HorSnchWdth(Tpix)         /* Horizontal Synchronization     */ \
-                                        /* pulse Width [1..64 Tpix]       */ \
-                        (((Tpix) - 1) << FShft (LCCR1_HSW))
-
-#define LCCR1_ELW       Fld (8, 16)     /* End-of-Line pixel clock Wait    */
-                                        /* count - 1 [Tpix]                */
-#define LCCR1_EndLnDel(Tpix)            /*  End-of-Line Delay              */ \
-                                        /*  [1..256 Tpix]                  */ \
-                        (((Tpix) - 1) << FShft (LCCR1_ELW))
-
-#define LCCR1_BLW       Fld (8, 24)     /* Beginning-of-Line pixel clock   */
-                                        /* Wait count - 1 [Tpix]           */
-#define LCCR1_BegLnDel(Tpix)            /*  Beginning-of-Line Delay        */ \
-                                        /*  [1..256 Tpix]                  */ \
-                        (((Tpix) - 1) << FShft (LCCR1_BLW))
-
-
-#define LCCR2_LPP       Fld (10, 0)     /* Line Per Panel - 1              */
-#define LCCR2_DisHght(Line)             /*  Display Height [1..1024 lines] */ \
-                        (((Line) - 1) << FShft (LCCR2_LPP))
-
-#define LCCR2_VSW       Fld (6, 10)     /* Vertical Synchronization pulse  */
-                                        /* Width - 1 [Tln] (L_FCLK)        */
-#define LCCR2_VrtSnchWdth(Tln)          /*  Vertical Synchronization pulse */ \
-                                        /*  Width [1..64 Tln]              */ \
-                        (((Tln) - 1) << FShft (LCCR2_VSW))
-
-#define LCCR2_EFW       Fld (8, 16)     /* End-of-Frame line clock Wait    */
-                                        /* count [Tln]                     */
-#define LCCR2_EndFrmDel(Tln)            /*  End-of-Frame Delay             */ \
-                                        /*  [0..255 Tln]                   */ \
-                        ((Tln) << FShft (LCCR2_EFW))
-
-#define LCCR2_BFW       Fld (8, 24)     /* Beginning-of-Frame line clock   */
-                                        /* Wait count [Tln]                */
-#define LCCR2_BegFrmDel(Tln)            /*  Beginning-of-Frame Delay       */ \
-                                        /*  [0..255 Tln]                   */ \
-                        ((Tln) << FShft (LCCR2_BFW))
-
-#if 0
-#define LCCR3_PCD	(0xff)		/* Pixel clock divisor */
-#define LCCR3_ACB	(0xff << 8)	/* AC Bias pin frequency */
-#define LCCR3_ACB_S	8
-#endif
-
-#define LCCR3_API	(0xf << 16)	/* AC Bias pin trasitions per interrupt */
-#define LCCR3_API_S	16
-#define LCCR3_VSP	(1 << 20)	/* vertical sync polarity */
-#define LCCR3_HSP	(1 << 21)	/* horizontal sync polarity */
-#define LCCR3_PCP	(1 << 22)	/* pixel clock polarity */
-#define LCCR3_OEP	(1 << 23)	/* output enable polarity */
-#if 0
-#define LCCR3_BPP	(7 << 24)	/* bits per pixel */
-#define LCCR3_BPP_S	24
-#endif
-#define LCCR3_DPC	(1 << 27)	/* double pixel clock mode */
-
-
-#define LCCR3_PCD       Fld (8, 0)      /* Pixel Clock Divisor */
-#define LCCR3_PixClkDiv(Div)            /* Pixel Clock Divisor */ \
-                        (((Div) << FShft (LCCR3_PCD)))
-
-
-#define LCCR3_BPP       Fld (3, 24)     /* Bit Per Pixel */
-#define LCCR3_Bpp(Bpp)                  /* Bit Per Pixel */ \
-                        (((Bpp) << FShft (LCCR3_BPP)))
-
-#define LCCR3_ACB       Fld (8, 8)      /* AC Bias */
-#define LCCR3_Acb(Acb)                  /* BAC Bias */ \
-                        (((Acb) << FShft (LCCR3_ACB)))
-
-#define LCCR3_HorSnchH  (LCCR3_HSP*0)   /*  Horizontal Synchronization     */
-                                        /*  pulse active High              */
-#define LCCR3_HorSnchL  (LCCR3_HSP*1)   /*  Horizontal Synchronization     */
-
-#define LCCR3_VrtSnchH  (LCCR3_VSP*0)   /*  Vertical Synchronization pulse */
-                                        /*  active High                    */
-#define LCCR3_VrtSnchL  (LCCR3_VSP*1)   /*  Vertical Synchronization pulse */
-                                        /*  active Low                     */
-
-#define LCSR_LDD	(1 << 0)	/* LCD Disable Done */
-#define LCSR_SOF	(1 << 1)	/* Start of frame */
-#define LCSR_BER	(1 << 2)	/* Bus error */
-#define LCSR_ABC	(1 << 3)	/* AC Bias count */
-#define LCSR_IUL	(1 << 4)	/* input FIFO underrun Lower panel */
-#define LCSR_IUU	(1 << 5)	/* input FIFO underrun Upper panel */
-#define LCSR_OU		(1 << 6)	/* output FIFO underrun */
-#define LCSR_QD		(1 << 7)	/* quick disable */
-#define LCSR_EOF	(1 << 8)	/* end of frame */
-#define LCSR_BS		(1 << 9)	/* branch status */
-#define LCSR_SINT	(1 << 10)	/* subsequent interrupt */
-
-#define LDCMD_PAL	(1 << 26)	/* instructs DMA to load palette buffer */
-
-#define LCSR_LDD	(1 << 0)	/* LCD Disable Done */
-#define LCSR_SOF	(1 << 1)	/* Start of frame */
-#define LCSR_BER	(1 << 2)	/* Bus error */
-#define LCSR_ABC	(1 << 3)	/* AC Bias count */
-#define LCSR_IUL	(1 << 4)	/* input FIFO underrun Lower panel */
-#define LCSR_IUU	(1 << 5)	/* input FIFO underrun Upper panel */
-#define LCSR_OU		(1 << 6)	/* output FIFO underrun */
-#define LCSR_QD		(1 << 7)	/* quick disable */
-#define LCSR_EOF	(1 << 8)	/* end of frame */
-#define LCSR_BS		(1 << 9)	/* branch status */
-#define LCSR_SINT	(1 << 10)	/* subsequent interrupt */
-
-#define LDCMD_PAL	(1 << 26)	/* instructs DMA to load palette buffer */
-
-/*
- * Memory controller
- */
-
-#define MEMC_BASE	__REG(0x48000000)  /* Base of Memory Controller */
-#define MDCNFG_OFFSET   0x0
-#define MDREFR_OFFSET   0x4
-#define MSC0_OFFSET     0x8
-#define MSC1_OFFSET     0xC
-#define MSC2_OFFSET     0x10
-#define MECR_OFFSET     0x14
-#define SXLCR_OFFSET    0x18
-#define SXCNFG_OFFSET   0x1C
-#define FLYCNFG_OFFSET  0x20
-#define SXMRS_OFFSET    0x24
-#define MCMEM0_OFFSET   0x28
-#define MCMEM1_OFFSET   0x2C
-#define MCATT0_OFFSET   0x30
-#define MCATT1_OFFSET   0x34
-#define MCIO0_OFFSET    0x38
-#define MCIO1_OFFSET    0x3C
-#define MDMRS_OFFSET    0x40
-	
-#define MDCNFG		__REG(0x48000000)  /* SDRAM Configuration Register 0 */
-#define MDCNFG_DE0	0x00000001
-#define MDCNFG_DE1	0x00000002
-#define MDCNFG_DE2	0x00010000
-#define MDCNFG_DE3	0x00020000
-#define MDCNFG_DWID0	0x00000004
-	
-#define MDREFR		__REG(0x48000004)  /* SDRAM Refresh Control Register */
-#define MSC0		__REG(0x48000008)  /* Static Memory Control Register 0 */
-#define MSC1		__REG(0x4800000C)  /* Static Memory Control Register 1 */
-#define MSC2		__REG(0x48000010)  /* Static Memory Control Register 2 */
-#define MECR		__REG(0x48000014)  /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
-#define SXLCR		__REG(0x48000018)  /* LCR value to be written to SDRAM-Timing Synchronous Flash */
-#define SXCNFG		__REG(0x4800001C)  /* Synchronous Static Memory Control Register */
-#define SXMRS		__REG(0x48000024)  /* MRS value to be written to Synchronous Flash or SMROM */
-#define MCMEM0		__REG(0x48000028)  /* Card interface Common Memory Space Socket 0 Timing */
-#define MCMEM1		__REG(0x4800002C)  /* Card interface Common Memory Space Socket 1 Timing */
-#define MCATT0		__REG(0x48000030)  /* Card interface Attribute Space Socket 0 Timing Configuration */
-#define MCATT1		__REG(0x48000034)  /* Card interface Attribute Space Socket 1 Timing Configuration */
-#define MCIO0		__REG(0x48000038)  /* Card interface I/O Space Socket 0 Timing Configuration */
-#define MCIO1		__REG(0x4800003C)  /* Card interface I/O Space Socket 1 Timing Configuration */
-#define MDMRS		__REG(0x48000040)  /* MRS value to be written to SDRAM */
-#define BOOT_DEF	__REG(0x48000044)  /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
-
-#define MDREFR_K2FREE	(1 << 25)	/* SDRAM Free-Running Control */
-#define MDREFR_K1FREE	(1 << 24)	/* SDRAM Free-Running Control */
-#define MDREFR_K0FREE	(1 << 23)	/* SDRAM Free-Running Control */
-#define MDREFR_SLFRSH	(1 << 22)	/* SDRAM Self-Refresh Control/Status */
-#define MDREFR_APD	(1 << 20)	/* SDRAM/SSRAM Auto-Power-Down Enable */
-#define MDREFR_K2DB2	(1 << 19)	/* SDCLK2 Divide by 2 Control/Status */
-#define MDREFR_K2RUN	(1 << 18)	/* SDCLK2 Run Control/Status */
-#define MDREFR_K1DB2	(1 << 17)	/* SDCLK1 Divide by 2 Control/Status */
-#define MDREFR_K1RUN	(1 << 16)	/* SDCLK1 Run Control/Status */
-#define MDREFR_E1PIN	(1 << 15)	/* SDCKE1 Level Control/Status */
-#define MDREFR_K0DB2	(1 << 14)	/* SDCLK0 Divide by 2 Control/Status */
-#define MDREFR_K0RUN	(1 << 13)	/* SDCLK0 Run Control/Status */
-#define MDREFR_E0PIN	(1 << 12)	/* SDCKE0 Level Control/Status */
-
-
-#endif